manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

140

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

The parameter has the following meaning: 

 

Parameter 

Description 

Range of values / note 

vapX 0/Y

 

 

VAP interface 

Enter a valid interface. 

AID

 

Connection ID of the 

client. 

-

 

For information on identifiers of addresses and interfaces, refer to the section "Interface 

identifiers and addresses (Page 25)". 

Result  

The table with the logged-on clients is displayed. 

6.1.1.11

 

show wlan data rates (access point) 

Description 

This command shows the tables with the available data transmission speeds.  

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call up the command with the following parameters: 

show wlan data rates <wlan 0/X>

 

The parameter has the following meaning: 

 

Parameter 

Description 

Range of values / note 

wlan 0/X

 

WLAN interface 

Enter a valid interface. 

For information on identifiers of addresses and interfaces, refer to the section "Interface 

identifiers and addresses (Page 25)". 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

COBHAM EXPLORER 5075GX Installation And User Manual preview
EXPLORER 5075GX
Brand: COBHAM Pages: 78
RR Electronic BISCAYA AIS Mounting Instructions preview
BISCAYA AIS
Brand: RR Electronic Pages: 8
Sea Tel 9711-44 KU-BAND TX/RX Installation And Operation Manual preview
9711-44 KU-BAND TX/RX
Brand: Sea Tel Pages: 256
B&B Electronics Wireless Antenna Installation Manual preview
Wireless Antenna
Brand: B&B Electronics Pages: 16
CommScope CMAX-DM CPUSE Series Installation Manual preview
CMAX-DM CPUSE Series
Brand: CommScope Pages: 4
Televes Ellipse 148920 Manual preview
Ellipse 148920
Brand: Televes Pages: 2
Televes MIRA BOSS Manual preview
MIRA BOSS
Brand: Televes Pages: 2
Sirio Antenne GPF 22 N Installation Manual preview
GPF 22 N
Brand: Sirio Antenne Pages: 2
Simrad 000-11640-001 Installation Manual preview
000-11640-001
Brand: Simrad Pages: 20
Microwave Radio Communications Ellipse 2000 Installation Manual preview
Ellipse 2000
Brand: Microwave Radio Communications Pages: 6
1byone OUK00-0494 Quick Start Manual preview
OUK00-0494
Brand: 1byone Pages: 2
1byone OUK00-0316 Quick Start Manual preview
OUK00-0316
Brand: 1byone Pages: 2
JCM Technologies ACTIVA Manual preview
ACTIVA
Brand: JCM Technologies Pages: 28
Jensen JAN139 Installation Instructions preview
JAN139
Brand: Jensen Pages: 2
REMO BAS-5101 Quick User Manual preview
BAS-5101
Brand: REMO Pages: 2
HP 8445B Operation And Service Manual preview
8445B
Brand: HP Pages: 154
Motorola AN720 Assembly And Installation Instructions Manual preview
AN720
Brand: Motorola Pages: 22
ETS-Lindgren 3106B User Manual preview
3106B
Brand: ETS-Lindgren Pages: 74

Brands by name

Popular brands

Load more brands