Siemens SIMATIC NET Page 163 Configuration Manual Download

Page: 163 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

163

The parameter has the following meaning:

Parameter

Description

Range of values / note

frames

Number of frames that are grouped to-

gether in one AMPDU data packet.

2...64
Default: 32

Result

The number of frames is specified.

Further notes

You display the setting with the

show wlan advanced-11n <wlan 0/X>

command.

6.1.5.9

wlan amsdu

Description

With this command, you enable the sending of A-MSDU data packets. Several MSDUs with

the same destination address are bundled into an A-MSDU and are sent together. This

reduces the network load. The function is enabled as default.

Requirement

●

The IEEE 802.11n transmission standard is enabled.

●

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-if-wlan-0-X)#

Syntax

Call the command without parameter assignment:

wlan amsdu

Result

The sending of A-MSDU data packets is enabled.

Further notes

You display the setting with the

show wlan advanced-11n <wlan 0/X>

command.

You disable the function with the

no wlan amsdu

command.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands