Siemens SIMATIC NET Page 98 Configuration Manual Download

Page: 98 / 464

Functions specific to SCALANCE

4.2 Signal recorder

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

wlan signal-recorder <wlan 0/X> <ms (100 - 60000)> display

The parameter has the following meaning:

Parameter

Description

Range of values / note

wlan 0/X

WLAN interface

Enter a valid interface.

The interval in milliseconds (ms) be-

tween acquisition of two measured

values

100 - 60000

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The recording is configured and will be started. The measured values are output in the CLI

and logged in files. If these files already exist, they will be overwritten.
Use the

wlan signal-recorder <wlan 0/X> stop

command to stop the recording.

During the recording, it is possible that working in the CLI becomes slower.

Further notes

You stop the recording early with the

wlan signal-recorder <wlan 0/X> stop

command.

You display the status of the signal recorder and the recording with the

show wlan signal-

recorder <wlan 0/X>

command.

4.2.5

wlan signal-recorder display sample_number (Client)

Description

With this command, you configure and start recording with the signal recorder. The

measured values are output in the CLI and logged in files. On completion of the recording,

the files can be downloaded as a zip file using http or tftp. The values are stored every 10

minutes. The file contains all values since the start of the recording.

Note
This command is only available in the client mode.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands