Siemens SIMATIC NET Page 117 Configuration Manual Download

Page: 117 / 464

System time

5.1 System time setting

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

117

The parameters have the following meaning:

Parameter

Description

Range of values / note

name

Name of the entry

maximum 16 characters

year

Year

1900 ... 2099

begin

Keyword for the start of daylight saving

time.

MMDDhh

Time for the start of daylight saving

time.

Time in the format

Month

Day

Hour

end

Keyword for the end of daylight saving

time.

MMDDhh

Time for the end of daylight saving

time.

Time in the format

Month

Day

Hour

Result

The entry for the start and end of daylight saving time was created.

5.1.2.4

time dst recurring

Description

With this command, you configure the start and end of daylight saving time with a generic

description.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

time dst recurring <name(16)> begin {<week(1-5)> | last} <weekday> <month> <hour> end

{<week(1-5)> | last} <weekday> <month> <hour>

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands