Siemens SIMATIC NET Page 206 Configuration Manual Download

Page: 206 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

206

Configuration Manual, 10/2015, C79000-G8976-C351-05

6.1.5.56

wlan rts-cts threshold

Description

With this command, you specify the packet size starting at which RTS/CTS (Request To

Send/Clear To Send) will be used.

Requirement

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-if-wlan-0-X)#

Syntax

Call up the command with the following parameters:

wlan rts-cts threshold < bytes(1-2346)>

The parameter has the following meaning:

Parameters

Description

Range of values / note

bytes

Size specified in bytes

1...2346

Default: 2346

Result

The packet size is specified.

Further notes

You display the setting with the

show wlan advanced <wlan 0/X>

command.

6.1.6

Commands in the VAP Interface Configuration mode

This section describes commands that you can call up in the VAP Interface Configuration

mode. Depending on the Interface selected, various command sets are available.
In the Global Configuration mode, enter the

interface vapX 0/Y

command to change to this

mode.

●

If you exit the VAP Interface Configuration mode with the

exit

command, you return to

the Global Configuration mode.

●

If you exit the VAP Interface Configuration mode with the

end

command, you return to the

Privileged EXEC mode.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands