manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Security and authentication 

 

10.2 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

397

 

10.2.2.7

 

no wlan security ap-radius-authenticator primary 

Description  

With this command, you disable the primary server. 

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

You are in the WLAN Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-wlan)#

 

Syntax 

Call up the command with the following parameters: 

no wlan security ap-radius-authenticator primary <index (1-2)>

 

The parameter has the following meaning: 

 

Parameters 

Description 

Range of values / note 

index

 

Index of the RADIUS server 

1...2 

Result  

The primary server is disabled. 

Further notes 

You enable the setting with the 

wlan security ap-radius-authenticator primary

 command. 

You display the setting with the 

show wlan security ap-radius-authenticator

 command. 

See also 

wlan security ap-radius-authenticator primary (Page 396) 
show wlan security ap-radius-authenticator (Access Point) (Page 389) 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Zehnder Rittling AX 40 Instructions Manual preview
AX 40
Brand: Zehnder Rittling Pages: 16
RF Elements StarterDish 21 UM Manual preview
StarterDish 21 UM
Brand: RF Elements Pages: 19
HyperLink Technologies HG2408P Installation Manual preview
HG2408P
Brand: HyperLink Technologies Pages: 18
DX Engineering DXE-MBVE-1UGBRT3 Instruction Manual preview
DXE-MBVE-1UGBRT3
Brand: DX Engineering Pages: 12
DX Antenna DTA3500 Instruction Manual preview
DTA3500
Brand: DX Antenna Pages: 3
DX Engineering DXE-4030VA-1 Manual preview
DXE-4030VA-1
Brand: DX Engineering Pages: 28
ETS-Lindgren 1052 User Manual preview
1052
Brand: ETS-Lindgren Pages: 23
ETS-Lindgren 3148B User Manual preview
3148B
Brand: ETS-Lindgren Pages: 41
EchoStar DISH 1000+ Installation Instructions Manual preview
DISH 1000+
Brand: EchoStar Pages: 28
Steren COM-835 User Manual preview
COM-835
Brand: Steren Pages: 8
SYNERGY SYSTEMS G-SynQ User Manual preview
G-SynQ
Brand: SYNERGY SYSTEMS Pages: 4
Clas Ohlson 32-4880 User Manual preview
32-4880
Brand: Clas Ohlson Pages: 5
Retro Antenna PA02 Installation Manual preview
PA02
Brand: Retro Antenna Pages: 4
Oehlbach Flat Style One User Manual preview
Flat Style One
Brand: Oehlbach Pages: 40
Garmin Gxm 51 Installation Instructions Manual preview
Gxm 51
Brand: Garmin Pages: 10
Feig Electronic OBID i-scan ID ISC.ANT.U170/170-FCC Installation Manual preview
OBID i-scan ID ISC.ANT.U170/170-FCC
Brand: Feig Electronic Pages: 12
BAS BAS-1318 GALAXY Series Quick User Manual preview
BAS-1318 GALAXY Series
Brand: BAS Pages: 2
Philips SDV6222T/27 User Manual preview
SDV6222T/27
Brand: Philips Pages: 10

Brands by name

Popular brands

Load more brands