manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Network structures 

 

6.2 VLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

233

 

Syntax 

Call up the command with the following parameters: 

switchport priority default <0-7>

 

The parameter has the following meaning: 

 

Parameter 

Description 

Range of values / note 

-

 

Value for the priority default 

0 ... 7 
Default: 0 

Result  

The setting for the default priority of the interface is configured. 

Further notes 

You reset the priority default to the original default with the 

no switchport priority default

 

command. 
You display this setting and other information with the 

show vlan port config

 command. 

6.2.3.7

 

no switchport priority default 

Description 

With this command, you reset the priority default for the interface to the default value.  
The default value is 0. 

Requirement 

You are in the Interface configuration mode. 
The command prompt is as follows: 

cli(config-if-$$$)#

 

Syntax 

Call the command without parameters: 

no switchport priority default

 

Result  

The setting is reset to the default value. 

Further notes 

You configure the priority default with the 

switchport priority default

 command. 

You display this setting and other information with the 

show vlan port config

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

camping first Satmex mobil 2 User Manual preview
Satmex mobil 2
Brand: camping first Pages: 40
albentia ACC-A24R-S Quick Installation Manual preview
ACC-A24R-S
Brand: albentia Pages: 2
HDView360 Mini-State HDMS9100 Instruction Manual preview
Mini-State HDMS9100
Brand: HDView360 Pages: 12
Sirius Satellite Radio Satellite Radio Antenna Installation Manual preview
Satellite Radio Antenna
Brand: Sirius Satellite Radio Pages: 10
Federal Signal Corporation OMNI-B Series Manual preview
OMNI-B Series
Brand: Federal Signal Corporation Pages: 4
Sea Tel 9797B-76 Installation And Operation Manual preview
9797B-76
Brand: Sea Tel Pages: 116
AvaLAN AW900XTP User Manual preview
AW900XTP
Brand: AvaLAN Pages: 8
Philips TT300 Product Information preview
TT300
Brand: Philips Pages: 2
Philips SDV7114A User Manual preview
SDV7114A
Brand: Philips Pages: 2
Philips SDV4401/27 Specification Sheet preview
SDV4401/27
Brand: Philips Pages: 2
Philips SDV2780 - HDTV Antenna - Indoor User Manual preview
SDV2780 - HDTV Antenna - Indoor
Brand: Philips Pages: 2
Philips SDV1227B/27 User Manual preview
SDV1227B/27
Brand: Philips Pages: 2
Philips SBCTT100/05 Instructions For Use Manual preview
SBCTT100/05
Brand: Philips Pages: 8
Philips SDV1121T/27 User Manual preview
SDV1121T/27
Brand: Philips Pages: 10
Philips SDW1850/17 User Manual preview
SDW1850/17
Brand: Philips Pages: 16
Philips SDV2720 - HDTV / TV User Manual preview
SDV2720 - HDTV / TV
Brand: Philips Pages: 16
Philips SDV2710 User Manual preview
SDV2710
Brand: Philips Pages: 16
Philips SDV4401/27 Manual preview
SDV4401/27
Brand: Philips Pages: 23

Brands by name

Popular brands

Load more brands