Siemens SIMATIC NET Page 444 Configuration Manual Download

Page: 444 / 464

Diagnostics

11.1 Diagnostics

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

444

Configuration Manual, 10/2015, C79000-G8976-C351-05

11.1.6.3

no client config

Description

With this command, you disable one of the clients that processes or forwards the messages

of the device.

Requirement

You are in the EVENTS Configuration mode.
The command prompt is as follows:

cli(config-events)#

Syntax

Call up the command with the following parameters:

no client config {syslog|trap|email|all}

The parameters have the following meaning:

Parameter

Description

syslog

Disables the client that sends the messages to the Syslog server

trap

Disables the client that sends the SNMP traps

Disables the client that sends the e-mails

all

Disables all clients at once

Result

The client selected for the transfer is disabled.

Further notes

You display the status of the events and the clients with the

show events config

command.

You enable the function with the

client config

command.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands