Siemens SIMATIC NET Page 446 Configuration Manual Download

Page: 446 / 464

Diagnostics

11.1 Diagnostics

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

446

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

event config {cold-warmstart|linkchange|authentication-failure|

power-change|faultstate-change|stp-change|

overlap-ap|wds|dfs|wlan-general|

wlan-auth-log|ipcf-cycle-time|ipcf-poll-

size|all}{logtable|syslog|email|trap|faults|all}

The parameters have the following meaning:

Parameter

Description

cold-warmstart

Message if there is cold or warm restart

linkchange

Message when there is a status change on a physical interface

authentication-failure

Message if there is an incorrect login

power-change

Message when there is a status change in the power supply

faultstate-change

Message when there is a status change in the error monitoring

stp-change

Message when there is a change in the spanning tree

overlap-ap

Message if radio channels overlap (in Access Point mode only)

wds

Message if there are changes to WDS (in Access Point mode only)

dfs

Message if a radar signal is received or if there is a status change in the DFS scan

(only in Access Point mode)

wlan-general

Message if the channel bandwidth has changed (in Access Point mode only)

wlan-auth-log

Message if changes are made to the log file (in Client mode only)

ipcf-cycle-time

Message if too many clients are logged on for the set iPCF cycle time or if some cli-

ents were not reached in one cycle

(only in access point mode and only available if supported by the device)

ipcf-poll-size

Message when the PNIO data size is too large for the transmission.

(only available if supported by the device)

all

All messages

logtable

Client that processes the logbook entries

syslog

Client that sends the messages to the log server

Client that sends the e-mails

trap

Client that sends the SNMP traps

faults

The device triggers an error. The error LED lights up.

all

All clients at once

Result

The setting deciding which message of the device is stored or forwarded is configured.

Further notes

You display the status of the events and the clients with the

show events config

command.

You delete the settings with the

no event config

command.

With this command, the clients are not enabled.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands