Siemens SIMATIC NET Page 450 Configuration Manual Download

Page: 450 / 464

Diagnostics

11.1 Diagnostics

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

450

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

no link {up|down}

The parameters have the following meaning:

Parameters

Description

Range of values / note

The message when establishing a connection is

disabled

down

The message when a connection is down is disa-

bled

Result

The settings for monitoring the physical network connections have been configured.

Further notes

You can display the current setting with the

show events faults config

command.

You enable the function with the

link

command.

11.1.6.8

send test mail

Description

With this command, you send an e-mail according to the currently configured SMTP settings.

Requirement

You are in the EVENTS configuration mode.
The command prompt is as follows:

cli(config-events)#

Syntax

Call the command without parameters:

send test mail

Result

An e-mail according to the currently configured SMTP settings is sent.

Further notes

You can display the current SMTP settings with the

show events smtp-server

command.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands