manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Security and authentication 

 

10.2 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

417

 

10.2.5

 

Commands in the VAP Interface configuration mode 

This section describes commands that you can call up in the VAP Interface Configuration 

mode. Depending on the Interface selected, various command sets are available.  
In the Global Configuration mode, enter the 

interface vapX 0/Y 

 command to change to this 

mode. 

●

 

If you exit the VAP Interface Configuration mode with the 

exit

 command, you return to 

the Global Configuration mode. 

●

 

If you exit the VAP Interface Configuration mode with the 

end

 command, you return to the 

Privileged EXEC mode. 

10.2.5.1

 

vap security authentication (access point) 

Description  

With this command, you specify the type of authentication. 

 

 

Note 
This command is available only in access point mode. 

 

 

Note 
iPCF or iPCF-MC mode enabled 
If iPCF or iPCF-MC mode is enabled, only "Open System" with the encryption method AES 

is supported in the security settings. 

 

Requirement 

You are in the Interface Configuration mode of the VAP interface. 
The command prompt is as follows:  

cli (config-if-vapX-0-Y)#

 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

SATMARK PAPSA User Manual preview
PAPSA
Brand: SATMARK Pages: 7
l-com HyperGain HG2424G Installation Instruction preview
HyperGain HG2424G
Brand: l-com Pages: 3
Fractus FR05-S1-E-0-103 User Manual preview
FR05-S1-E-0-103
Brand: Fractus Pages: 12
RADIOHAUS SPIDERDXMAN RH-DX1020 Assembly Instructions Manual preview
SPIDERDXMAN RH-DX1020
Brand: RADIOHAUS Pages: 11
1 BY ONE 202UK-0005 Quick Start Manual preview
202UK-0005
Brand: 1 BY ONE Pages: 2
Panorama Antennas GPSD Series Installation Instructions preview
GPSD Series
Brand: Panorama Antennas Pages: 2
Panorama Antennas WMM9G Series Installation Instructions Manual preview
WMM9G Series
Brand: Panorama Antennas Pages: 8
DX Engineering DXE-MBVE-1UGBRT3 Instruction Manual preview
DXE-MBVE-1UGBRT3
Brand: DX Engineering Pages: 12
DX Antenna DTA3500 Instruction Manual preview
DTA3500
Brand: DX Antenna Pages: 3
DX Engineering DXE-4030VA-1 Manual preview
DXE-4030VA-1
Brand: DX Engineering Pages: 28
Antenna Experts LP-500-2500 Installation Manual preview
LP-500-2500
Brand: Antenna Experts Pages: 1
Audio Technica ATW-A62P Installation And Operation preview
ATW-A62P
Brand: Audio Technica Pages: 4
Sarantel SL1300 Soldering Manuallines preview
SL1300
Brand: Sarantel Pages: 4
CommScope CMAX Series Installation Instruction preview
CMAX Series
Brand: CommScope Pages: 6
CommScope CMAX Series Installation Manual preview
CMAX Series
Brand: CommScope Pages: 8
SteppIR MonstIR Installation Instructions Manual preview
MonstIR
Brand: SteppIR Pages: 46
SteppIR UrbanBeam Yagi Assembly Manual preview
UrbanBeam Yagi
Brand: SteppIR Pages: 52
RCA ANT850E Installation Manual preview
ANT850E
Brand: RCA Pages: 16

Brands by name

Popular brands

Load more brands