Siemens SIMATIC NET Page 77 Configuration Manual Download

Page: 77 / 464

Configuration

3.2 Load and Save

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

3.2.5.4

tftp save

Description

With this command, you copy a file from the file system of the device to a TFTP server. The

TFTP protocol is used for the transfer. You can also display a list of available files.

Requirement

●

The name of the file is specified

●

You are in the LOADSAVE configuration mode.

The command prompt is:

cli(config-loadsave)#

Syntax

Call up the command with the following parameters:

tftp save {showfiles|filetype<filetype>}

The parameters have the following meaning:

Parameter

Description

Range of values / note

showfiles

Shows the available files

filetype

Keyword for a file type to be loaded

filetype

Name of the file type

max. 100 characters

Result

The file types are displayed or the file is copied.

Further notes

You configure the name of the file with the

tftp filename

command.

With the "

show loadsave files

" command, you can display the file types.

3.2.5.5

tftp server

Description

With this command, you configure the access to a TFTP server.

Requirement

You are in the LOADSAVE configuration mode.
The command prompt is as follows:

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands