manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Functions specific to SCALANCE 

 

4.4 iPCF-MC 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

107

 

4.4.2.4

 

wlan ipcf-mc mgmt-scan-period (client) 

 

 

Note 
The command is only available with the following device: 

•

 

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 

(US version)) 

 

Description 

With this command, you the time for the background scan interval as a multiple of the update 

time. 

Requirement 

The SCALANCE W700 device is in client mode 
You are in the WLAN configuration mode. 
The command prompt is as follows:  

cli(config-wlan)#

 

Syntax 

Call up the command with the following parameters: 

wlan ipcf-mc mgmt-scan-period <num-of-cycles (1-10)>

 

The parameter has the following meaning: 

 

Parameter 

Description 

Range of values / note 

num-of-cycles

 

Duration  

1 ... 10 

Result  

The time is set. 

Further notes 

You display the setting with the 

show wlan ipcf-mc

 command. 

 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Chameleon Antenna CHA MPAS 2.0 Operator'S Manual preview
CHA MPAS 2.0
Brand: Chameleon Antenna Pages: 25
Hama 00136677 Operating Instruction preview
00136677
Brand: Hama Pages: 8
W6LVP Amplified Receive-Only Magnetic Loop Antenna Quick Start Manual preview
Amplified Receive-Only Magnetic Loop Antenna
Brand: W6LVP Pages: 2
Duratrax DTXP3110 Instructions preview
DTXP3110
Brand: Duratrax Pages: 2
K&M Burkhard Reuter RLA4GS Specification And Operator'S Manual preview
RLA4GS
Brand: K&M Burkhard Reuter Pages: 8
cahors 3579431409999 User Manual preview
3579431409999
Brand: cahors Pages: 50
Radio Shack TV FM High Gain Mast-Mount Antenna UHF/VHF/FM Amplifier with Switchable FM... User Manual preview
TV FM High Gain Mast-Mount Antenna UHF/VHF/FM Amplifier with Switchable FM...
Brand: Radio Shack Pages: 8
King-Dome 9754-LP Installation And Operating Instructions Manual preview
9754-LP
Brand: King-Dome Pages: 40
Philips SDV6122T/27 User Manual preview
SDV6122T/27
Brand: Philips Pages: 10
Strong Technologies SRT D85W Instructions Manual preview
SRT D85W
Brand: Strong Technologies Pages: 9
Barrett 2081-02-01 Installation Instructions preview
2081-02-01
Brand: Barrett Pages: 4
Barrett 2019 User Manual preview
2019
Brand: Barrett Pages: 22
One for All SV-9380 Instruction Manual preview
SV-9380
Brand: One for All Pages: 2
One for All SV-9385 Instruction Manual preview
SV-9385
Brand: One for All Pages: 2
One for All SV-9153 Instruction Manual preview
SV-9153
Brand: One for All Pages: 2
Sirio Antenne HP 140-175 Installation Manual preview
HP 140-175
Brand: Sirio Antenne Pages: 2
IKUSI mini FLASHD Quick Start Manual preview
mini FLASHD
Brand: IKUSI Pages: 3
Radeus 8000 ACS Series Operation & Maintenance Manual preview
8000 ACS Series
Brand: Radeus Pages: 174

Brands by name

Popular brands

Load more brands