Siemens SIMATIC NET Page 421 Configuration Manual Download

Page: 421 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

421

10.2.5.4

vap security encryption (access point)

Description

With this command, you enable encryption with a fixed (unchanging) WEP key. You can only

enable or disable encryption if you have selected "Open System" for authentication. All other

security methods include both authentication and encryption. If you use "Open system" with

"Encryption" or "Shared Key", you always need to specify the WEP key used for the

encryption.

Note
This command is available only in access point mode.

Requirement

●

The type of authentication is "

open-system

You are in the Interface Configuration mode of the VAP interface.
The command prompt is as follows:

cli (config-if-vapX-0-Y)#

Syntax

Call the command without parameter assignment:

vap security encryption

Result

The encryption is enabled. You can only disable encryption if you have selected "

open-sytem

for authentication

Further notes

You display the settings with the

show wlan security <vapX 0/Y>

command.

You disable the encryption with the

no vap security encryption

command.

You define a WEP key with the

wlan security edit key

command.

With the

vap security default-key (Access Point)

command, you configure the WEP key

used for encryption.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands