Siemens SIMATIC NET Page 167 Configuration Manual Download

Page: 167 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

167

The parameters have the following meaning:

Parameter

Description

Range of values / note

index

Antenna connector

meter

Cable length in meters [m]

0...30
Default: 0

Result

The cable length is specified.

Further notes

You show the set cable length with the

show wlan antennas <wlan 0/X>

command.

6.1.5.14

wlan antenna gain-2-4GHz

Description

With this command, you specify the antenna gain of the antenna type "User defined" in the

2.4 GHz frequency band. With the

show wlan basic

command, check whether the maximum

transmit power is exceeded with the setting.

Requirement

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-if-wlan-0-X)#

Syntax

Call up the command with the following parameters:

wlan antenna gain-2-4GHz <index(1)> <dBi(0-30)>

The parameters have the following meaning:

Parameter

Description

Range of values / note

index

Antenna connector

gain value

Antenna gain in decibels isotropic (dBi)

0 ... 30
0 = antenna is not connected

Result

The antenna gain is specified.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands