manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Security and authentication 

 

10.2 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

403

 

10.2.3

 

Commands in the WLAN Interface configuration mode 

This section describes commands that you can call up in the WLAN Interface Configuration 

mode. Depending on the Interface selected, various command sets are available.  
In the Global Configuration mode, enter the 

interface wlan 0/X

 command to change to this 

mode. 

●

 

If you exit the WLAN Interface Configuration mode with the 

exit

 command, you return to 

the Global Configuration mode. 

●

 

If you exit the WLAN Interface Configuration mode with the 

end

 command, you return to 

the Privileged EXEC mode. 

10.2.3.1

 

wlan security edit key 

Description  

With this command, you add a WEP or AES key to the key table. You can choose between 

several key lengths. 

●

 

5 or 13 ASCII or 10 or 26 hexadecimal characters specify a weaker key (40/104 bits). 

●

 

16 ASCII or 32 hexadecimal characters, on the other hand, define a strong key (128 bits). 

 

 

Note 
iPCF or iPCF-MC mode activated 
If you want encryption with AES in iPCF or iPCF-MC mode, only keys with a 128 bit key 

length are supported. 

 

Requirement 

You are in the Interface configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan security edit key <index(1-4)> <key>

 

The parameters have the following meaning: 

 

Parameter 

Description 

Range of values / note 

index

 

Index of the key table 

1...4 

key

 

Key 

Enter the WEP or AES key. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Naxa NAA-303 Operation Manual preview
NAA-303
Brand: Naxa Pages: 2
M2 Antenna Systems 20M4DX Assembly Manual preview
20M4DX
Brand: M2 Antenna Systems Pages: 8
Palomar BULLET-2006 Product Manual preview
BULLET-2006
Brand: Palomar Pages: 5
ADC Spectrum 7.0 Installation Manuals preview
Spectrum 7.0
Brand: ADC Pages: 20
stellar labs 30-2476 Installation Manual preview
30-2476
Brand: stellar labs Pages: 2
RF Elements Sector Carrier Class 5-17 Installation Manual preview
Sector Carrier Class 5-17
Brand: RF Elements Pages: 12
M2 Antenna Systems 40M4LLDD Assembly Manual preview
40M4LLDD
Brand: M2 Antenna Systems Pages: 14
New Eagle C4MAX v2 Installation Manual preview
C4MAX v2
Brand: New Eagle Pages: 14
WiMo CK-868LIN Manual preview
CK-868LIN
Brand: WiMo Pages: 3
Televes TRINOVA BOSS User Manual preview
TRINOVA BOSS
Brand: Televes Pages: 12
Vislink Mantis Motorised MSAT ACU User Manual preview
Mantis Motorised MSAT ACU
Brand: Vislink Pages: 60
Sirio Antenne GP 87-108 LB Installation Manual preview
GP 87-108 LB
Brand: Sirio Antenne Pages: 4
Steren BF-320 User Manual preview
BF-320
Brand: Steren Pages: 6
1byone OUS00-0568 Manual preview
OUS00-0568
Brand: 1byone Pages: 2
Steren ANT-9026 Instruction Manual preview
ANT-9026
Brand: Steren Pages: 2
Melchioni SATURN AV-9003S Instruction Manual preview
SATURN AV-9003S
Brand: Melchioni Pages: 8
Hawking HAI7SIP User Manual preview
HAI7SIP
Brand: Hawking Pages: 15
CUSHCRAFT LFA-6M8EL Instruction Manual preview
LFA-6M8EL
Brand: CUSHCRAFT Pages: 12

Brands by name

Popular brands

Load more brands