manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Layer 3 functions 

 

9.1 NAT 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

372

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

Syntax 

Call the command without parameters: 

show nat

 

Result  

The configuration and the translation list are displayed. 

See also 

nat (Client) (Page 373) 
nat local ip address (Client) (Page 376) 
nat interface (Client) (Page 377) 
nat timeout (Client) (Page 379) 

9.1.2

 

Commands in the global configuration mode 

This section describes commands that you can call up in the Global configuration mode. 
In Privileged EXEC mode, enter the 

configure terminal

 command to change to this mode. 

Commands relating to other topics that can be called in the Global configuration mode can 

be found in the relevant sections. 
You exit the Global configuration mode with the 

end

 or 

exit

 command and are then in the 

Privileged EXEC mode again. 

9.1.2.1

 

nat (client) 

 

 

Note 
This command is only available in the client mode. 

 

Description 

With this command, you change to the NAT Configuration mode.  

Requirement 

You are in the Global Configuration mode. 
The command prompt is as follows: 

cli(config)#

 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

M2 Antenna Systems 222-10EZ Assembly Manual preview
222-10EZ
Brand: M2 Antenna Systems Pages: 5
Applied Satellite Engineering ASE AA511 Quick Start Manual preview
ASE AA511
Brand: Applied Satellite Engineering Pages: 6
M2 Antenna Systems 40M1L Manual preview
40M1L
Brand: M2 Antenna Systems Pages: 9
Cabletron Systems RoamAbout 802.11 Supplementary Manual preview
RoamAbout 802.11
Brand: Cabletron Systems Pages: 24
Televes SMATV 630 Mounting Instructions preview
SMATV 630
Brand: Televes Pages: 2
SteppIR 2 Element Yagi Instruction Manual preview
2 Element Yagi
Brand: SteppIR Pages: 42
Xirrus XR-2425H Quick Installation Manual preview
XR-2425H
Brand: Xirrus Pages: 26
Label Italy AKL/8M Mounting Instructions preview
AKL/8M
Brand: Label Italy Pages: 7
A.H. Systems AK-4G Operation Manual preview
AK-4G
Brand: A.H. Systems Pages: 9
A.H. Systems 2383 Operation Manual preview
2383
Brand: A.H. Systems Pages: 15
Lab-T LavvieBeacon User Manual preview
LavvieBeacon
Brand: Lab-T Pages: 4
Hawking HA12W User Manual preview
HA12W
Brand: Hawking Pages: 14
Tarheel Antennas 400A Instruction Manual preview
400A
Brand: Tarheel Antennas Pages: 9
Tarheel Antennas MFJ-1792 Instruction Manual preview
MFJ-1792
Brand: Tarheel Antennas Pages: 15
CUSHCRAFT LFA-6M8EL Instruction Manual preview
LFA-6M8EL
Brand: CUSHCRAFT Pages: 12
AST AD511-2 User Manual preview
AD511-2
Brand: AST Pages: 7
NoCable 70 Manual preview
70
Brand: NoCable Pages: 6
DAPAudio EDGE EOA-1 User Manual preview
EDGE EOA-1
Brand: DAPAudio Pages: 16

Brands by name

Popular brands

Load more brands