manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

System time 

 

5.3 SNTP client 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

124

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

5.3.1.1

 

show sntp broadcast-mode status 

Description 

This command shows the current configuration of the broadcast mode of SNTP.  

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call the command without parameters: 

show sntp broadcast-mode status

 

Result  

The current SNTP broadcast configuration is displayed. 

5.3.1.2

 

show sntp status 

Description 

This command shows the settings of the Simple Network Time Protocol.  

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call the command without parameters: 

show sntp status

 

Result  

The settings of SNTP are displayed. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

H3C ANT-2015Y Manual preview
ANT-2015Y
Brand: H3C Pages: 6
Ebyte TXWF-PCB-3214 User Manual preview
TXWF-PCB-3214
Brand: Ebyte Pages: 6
AEI Security & Communications DGXDSDV111SMA-2KM Manual preview
DGXDSDV111SMA-2KM
Brand: AEI Security & Communications Pages: 56
THOMSON ANT1706 Operating Instruction preview
ANT1706
Brand: THOMSON Pages: 38
WADE Antenna, Inc. PB-81 Instruction Sheet preview
PB-81
Brand: WADE Antenna, Inc. Pages: 5
Televes NOVA Manual preview
NOVA
Brand: Televes Pages: 28
Panorama Antennas GPSP Series Installation Instruction preview
GPSP Series
Brand: Panorama Antennas Pages: 2
Feig Electronic OBID i-scan ID ISC.ANT300 Montage, Installation preview
OBID i-scan ID ISC.ANT300
Brand: Feig Electronic Pages: 43
Zonet ZWA1207 Manual preview
ZWA1207
Brand: Zonet Pages: 6
Parker 165787 User Manual preview
165787
Brand: Parker Pages: 18
Ubiquiti Horn-5-90 Quick Start Manual preview
Horn-5-90
Brand: Ubiquiti Pages: 4
Ubiquiti Power Beam m5 PBE-M5-620 Quick Start Manual preview
Power Beam m5 PBE-M5-620
Brand: Ubiquiti Pages: 28
Kathrein 80010735V01 Manual preview
80010735V01
Brand: Kathrein Pages: 7
Ramsey Electronics WSA2M Quick Start Manual preview
WSA2M
Brand: Ramsey Electronics Pages: 2
Comba Telecom CriticalPoint UHF DAS User Manual preview
CriticalPoint UHF DAS
Brand: Comba Telecom Pages: 42
Com-Power AH-118 Manual preview
AH-118
Brand: Com-Power Pages: 11
Renkforce 1404040 Operating Instructions Manual preview
1404040
Brand: Renkforce Pages: 8
Beyerdynamic Planar Antenna CA 2413 Specification Sheet preview
Planar Antenna CA 2413
Brand: Beyerdynamic Pages: 2

Brands by name

Popular brands

Load more brands