Siemens SIMATIC NET Page 123 Configuration Manual Download

Page: 123 / 464

System time

5.3 SNTP client

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

123

Syntax

Call up the command with the following parameters:

ntp time diff <(+/-hh:mm)>

The parameter has the following meaning:

Parameter

Description

Time zones to the west of the NTP server time zone

Time zones to the east of the NTP server time zone

Number of hours difference

Number of minutes difference

Enter the number of hours and number of minutes with two digits each.
Default: No time difference.

Result

The time difference between the device and the NTP server is configured.

5.3

SNTP client

This section describes commands relevant for configuration of the SNTP client.

5.3.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands