manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual, Page: 254 / 464

Share
Download
Siemens SIMATIC NET Configuration Manual Download Page 254

Network structures 

 

6.3 Spanning Tree 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

254

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

Result  

The automatic discovery of a bridge on the interface is disabled. 

Further notes 

You enable the automatic detection with the 

spanning-tree l2t-auto-edge

 command. 

You can display the status of this function with the 

show spanning-tree l2t-edge

command. 

6.3.3.7

 

spanning-tree l2t-edge 

Description 

With this command, you specify that an end device can be located at a layer 2 tunnel port. 

Otherwise a reconfiguration of the network will be triggered whenever a link to this port is 

modified. The L2T clients should be interconnected.   

Requirement 

You are in the Global Configuration mode. 
The command prompt is as follows: 

cli(config)#

 

Syntax 

Call the command without parameters: 

spanning-tree l2t-edge

 

Result  

The setting is enabled. 

Further notes 

You disable the setting with the 

no spanning-tree l2t-edge

 command. 

You can display the status of this function with the 

show spanning-tree l2t-edge

command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments