Siemens SIMATIC NET Page 393 Configuration Manual Download

Page: 393 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

393

10.2.2.3

wlan security ap-radius-authenticator address

Description

With this command, you configure the IP address of the RADIUS server.

Note
This command is available only in access point mode.

Requirement

You are in the WLAN Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-wlan)#

Syntax

Call up the command with the following parameters:

wlan security ap-radius-authenticator address <index (1-2)> {ipv4 <ucast_addr> |

fqdn-name <FQDN>}

The parameters have the following meaning:

Parameter

Description

Range of values / note

index

Index of the RADIUS server

1...2

ipv4

Keyword for an IPv4 address

ucast_addr

IPv4 address

Enter a valid IPv4 address.

fqdn-name

Keyword for a domain name

FQDN

Domain name (Fully Qualified Domain Name) Maximum of 100 characters

Result

The RADIUS server is enabled.

Further notes

You display the setting with the

show wlan security ap-radius-authenticator

command.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands