Siemens SIMATIC NET Page 78 Configuration Manual Download | Manualshive

Page: 78 / 464

background image

Configuration

3.2 Load and Save

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

78

Configuration Manual, 10/2015, C79000-G8976-C351-05

cli(config-loadsave)#

Syntax

Call up the command with the following parameters:

tftp server {ipv4 <ucast-addr> | fqdn-name <FQDN>} [port<tcp port(1-65535)>]

The parameters have the following meaning:

Parameter

Description

Range of values / note

ipv4

Keyword for an IPv4 address

-

ucast-addr

Value for an IPv4 unicast address

Enter a valid IPv4 unicast ad-

dress.

fqdn-name

Keyword for a domain name

-

FQDN

Domain name (Fully Qualified Domain

Name)

Maximum 100 characters

port

Keyword for the port of the server via

which the TFTP connection runs

-

tcp port

Number of the port

1 … 65535

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The settings for the access to the selected TFTP server are configured.

3.2.5.6

password

Description

With this command, you activate and configure the password for encrypted certificates.
User, server or HTTPS certificates can exist as PKCS#12 certificates (.p12 and .pfx) and

PEM certificates (.pem).

Note
User and server certificate in one file
If the user and the server certificate are located in the same file, load this file on the device

as the user certificate and as the server certificate.

Requirement

You are in the LOADSAVE configuration mode.
The command prompt is as follows:

cli(config-loadsave)#

«
...
76
77
78
79
80
...
»

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Brand: One for All Pages: 40

Brand: Marquant Pages: 16

Brand: Antop Pages: 7

M6060060P1D43602V

Brand: Ventev Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 10

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 12

Brand: Philips Pages: 12

Brand: Philips Pages: 2

Brand: Philips Pages: 11

Brand: Philips Pages: 2

Brand: Philips Pages: 1

Brand: Philips Pages: 11

Brand: Philips Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands