manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

158

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

6.1.5.3

 

no wlan allowed channels only 

Description   

With this command, you disable the "

Use allowed channels only

" function. This is the default 

setting. 

Requirement 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call the command without parameter assignment: 

no wlan allowed channels only

 

Result  

The function is disabled. 

Further notes 

You display the setting with the 

show wlan allowed channels <wlan 0/X>

 command.  

You enable the function with the 

 wlan allowed channels only

 command.  

See also 

wlan allowed channels only (Page 157) 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Feig Electronic OBID ID ISC.ANT340/240-A Installation Manual preview
OBID ID ISC.ANT340/240-A
Brand: Feig Electronic Pages: 28
Winegard Carryout G2+ Instruction Manual preview
Carryout G2+
Brand: Winegard Pages: 8
Dish Network DISH 1000.2 Installation Manual preview
DISH 1000.2
Brand: Dish Network Pages: 22
Winegard Movin' View MV-0500 Owner'S Manual preview
Movin' View MV-0500
Brand: Winegard Pages: 12
Motec Systems GPS- G1(T) User Manual preview
GPS- G1(T)
Brand: Motec Systems Pages: 7
Aerohive AP350 User Manual preview
AP350
Brand: Aerohive Pages: 24
Garmin NavTalk Pilot Pilot'S Manual & Reference preview
NavTalk Pilot
Brand: Garmin Pages: 176
Steren COM-835 User Manual preview
COM-835
Brand: Steren Pages: 8
M2 Antenna Systems 11M5DX Quick Start Manual preview
11M5DX
Brand: M2 Antenna Systems Pages: 7
Deger D25H Assembly And Operating Manual preview
D25H
Brand: Deger Pages: 43
Hawking Hi-Gain HD9DP Quick Installation Manual preview
Hi-Gain HD9DP
Brand: Hawking Pages: 2
Labgear LABHG52T User Manual preview
LABHG52T
Brand: Labgear Pages: 2
Supersonic SC-603 User Manual preview
SC-603
Brand: Supersonic Pages: 2
M2 Antenna Systems SYSTEM SAMPLE 3 Assembly Manual preview
SYSTEM SAMPLE 3
Brand: M2 Antenna Systems Pages: 16
Hama 179823 Operating Instructions Manual preview
179823
Brand: Hama Pages: 22
Xirrus 2x2 Omni Antenna Reference Manual preview
2x2 Omni Antenna
Brand: Xirrus Pages: 12
Garmin GMR 430 XHD3 Series Installation Instructions Manual preview
GMR 430 XHD3 Series
Brand: Garmin Pages: 20
Ebyte TX868-JZLW-15 User Manual preview
TX868-JZLW-15
Brand: Ebyte Pages: 6

Brands by name

Popular brands

Load more brands