manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual, Page: 283 / 464

Share
Download
Siemens SIMATIC NET Configuration Manual Download Page 283

 

Network protocols 

 

7.1 IPv4 protocol 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

283

 

7.1.1.3

 

show ip route 

Description 

This command shows the routes currently being used.  

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call up the command with the following parameters: 

show ip route[{<ip-address>[<mask>]|connected|static}]

 

The parameters have the following meaning: 

 

Parameter 

Description 

Range of values / 

note 

ip-address

  shows the information for a specific IP address 

enter a valid IP ad-

dress 

mask

 

defines an address range using the subnet mask 

/8, /16 or /24 

connected

 

Shows the direct connections 

- 

static

 

Shows the static connections 

- 

Result  

The routing table is displayed. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments