Siemens SIMATIC NET Page 342 Configuration Manual Download

Page: 342 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

342

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

snmp notify <NotifyName> tag <TagName> type {Trap|Inform}

[{volatile|nonvolatile}]]

The parameters have the following meaning:

Parameter

Description

Range of values / note

NotifyName

Name of the SNMP notification

max. 32 characters

tag

Keyword for a target key

TagName

Name of the target key

max. 32 characters

Type

Type of the SNMP notification

•

Trap

generates a trap

•

Inform

generates a log entry or sends

an entry to the log server

Storage type

specifies whether the settings remain

following a restart:

•

volatile

(volatile):

The settings are lost after a

restart

•

nonvolatile

(non-volatile):

The settings are retained after

a restart

Result

The details of the SNMP notifications are configured.

Further notes

You delete the details of an SNMP group with the

no snmp notify

command.

You display the configured SNMP notifications with the

show snmp notif

command.

You display the configured SNMP target addresses with the

show snmp targetaddr

command.

7.4.2.13

no snmp notify

Description

With this command, you delete the details of the SNMP notifications.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands