Siemens SIMATIC NET Page 406 Configuration Manual Download

Page: 406 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

406

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

wlan security authentication { show-methods | methods }

The parameters have the following meaning:

Parameter

Description

Range of values / note

show-
methods

Lists the available types of

authentication

•

open-system

Without authentication. Encryption with a fixed (un-

changing) key can be selected as an option. To ena-

ble encryption, use the "

wlan security

encryption

" command.

•

shared-key

A fixed key is stored for authentication.

•

wpa (Radius)

WPA authentication.

•

wpa-psk

WPA authentication without RADIUS server.

•

wpa2 (Radius)

WPA2 authentication.

•

wpa2-psk

WPA2 authentication without RADIUS server.

•

wpa-wpa2-auto (Radius)

WPA and WPA2 authentication

•

wpa-wpa2-auto-psk

WPA and WPA2 authentication without a RADIUS

server

methods

Value corresponding to an

authentication method.

Result

The type of authentication is specified.

Further notes

You display the settings with the

show wlan security

command.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands