Siemens SIMATIC NET Page 248 Configuration Manual Download

Page: 248 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

248

Configuration Manual, 10/2015, C79000-G8976-C351-05

6.3.1.9

show spanning-tree root

Description

This command shows the settings of the root bridge for the spanning tree function.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show spanning-tree root

[{address|cost|forward-time|id|max-age|port|priority|detail}]

The parameters have the following meaning:

Parameter

Description

address

Shows the MAC address of the root bridge

cost

Shows the costs of the connection to the root bridge.

forward-time

Shows the time that the bridge is in the listening mode when changing from

the blocking mode to the learning mode

Shows the ID of the root bridge

max-age

Shows the maximum age of the data packet after which it is deleted

port

Shows the interface via which the spanning tree is set up

priority

Shows the priority of the bridge

detail

Shows detailed information about the root bridge

Result

The settings of the root bridge for the spanning tree function are displayed.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands