manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

162

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

Requirement 

●

 

The IEEE 802.11n transmission standard is enabled. 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan ampdu bytes-limit <bytes(1024-65535)>

 

The parameter has the following meaning: 

 

Parameters 

Description 

Range of values / note 

bytes

 

Size of the AMPDU data packet in bytes  1024 to 65535 bytes 

Default: 50000 bytes 

Result  

The size for the AMPDU data packets is specified. 

Further notes 

You display the setting with the 

show wlan advanced-11n <wlan 0/X>

 command. 

6.1.5.8

 

wlan ampdu frames-limit 

Description  

With this command, you specify the number of individual data packets (frames) grouped 

together in one AMPDU data packet.  

Requirement 

●

 

The IEEE 802.11n transmission standard is enabled. 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan ampdu frames-limit <frames(2-64)>

 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Garmin NavTalk Pilot Installation Manual preview
NavTalk Pilot
Brand: Garmin Pages: 10
L3 Narda ADFA Handling And Safety Instructions preview
Narda ADFA
Brand: L3 Pages: 122
Icom AL-705 Assembly Instructions Manual preview
AL-705
Brand: Icom Pages: 10
Panorama Antennas SW3-606 Installation Instructions Manual preview
SW3-606
Brand: Panorama Antennas Pages: 2
TERK Technologies PI-B Owner'S Manual preview
PI-B
Brand: TERK Technologies Pages: 6
Velleman ANTDVBT7 User Manual preview
ANTDVBT7
Brand: Velleman Pages: 5
Jatontec JT8500D Administrator User Manual preview
JT8500D
Brand: Jatontec Pages: 36
A.H. Systems SAS-521-4 Operation Manual preview
SAS-521-4
Brand: A.H. Systems Pages: 15
A.H. Systems SAS-521-2 Operation Manual preview
SAS-521-2
Brand: A.H. Systems Pages: 15
A.H. Systems SAS-545 Operation Manual preview
SAS-545
Brand: A.H. Systems Pages: 19
Siemens 6GK5792-8DR00-0AA6 Operating Instructions Manual preview
6GK5792-8DR00-0AA6
Brand: Siemens Pages: 26
Buddipole Buddistick PRO Quick Start Manual preview
Buddistick PRO
Brand: Buddipole Pages: 3
Audio Technica ATW-A49 Installation And Operation preview
ATW-A49
Brand: Audio Technica Pages: 2
Televes DATBOSSMIX LR Quick Start Manual preview
DATBOSSMIX LR
Brand: Televes Pages: 4
TechniSat DIGIDISH 33 Installation Instructions Manual preview
DIGIDISH 33
Brand: TechniSat Pages: 84
Extreme Networks WS-AP3801i Quick Reference preview
WS-AP3801i
Brand: Extreme Networks Pages: 6
Laird CUSHCRAFT S51514WP Assembly And Installation Instructions preview
CUSHCRAFT S51514WP
Brand: Laird Pages: 2
1byone O0000-0683 Instruction Manual preview
O0000-0683
Brand: 1byone Pages: 2

Brands by name

Popular brands

Load more brands