Siemens SIMATIC NET Page 92 Configuration Manual Download

Page: 92 / 464

Functions specific to SCALANCE

4.1 WBM

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

4.1.1.1

show web-session-timeout

Description

This command shows the timeout setting for the WBM.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show web-session-timeout

Result

The timeout setting for the WBM is displayed.

4.1.2

Commands in the global configuration mode

This section describes commands that you can call up in the Global configuration mode.
In Privileged EXEC mode, enter the

configure terminal

command to change to this mode.

Commands relating to other topics that can be called in the Global configuration mode can

be found in the relevant sections.
You exit the Global configuration mode with the

end

exit

command and are then in the

Privileged EXEC mode again.

4.1.2.1

web-session-timeout

Description

With this command, you enable the automatic logoff and you configure the timeout setting for

the WBM.

Requirement

You are in the Global configuration mode.
The command prompt is as follows:

cli(config)#

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands