Siemens SIMATIC NET Page 243 Configuration Manual Download

Page: 243 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

243

Syntax

Call up the command with the following parameters:

show spanning-tree active [detail]

The parameter has the following meaning:

Parameter

Description

detail

Shows settings in detail

Result

The settings for the active ports of the spanning tree function are displayed.

6.3.1.3

show spanning-tree bridge

Description

This command shows the settings of the spanning tree function of the bridge.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show spanning-tree bridge

[{address|forward-time|hello-time|id|max-age|protocol|priority|detail}]

The parameters have the following meaning:

Parameter

Description

address

Shows the MAC address of the bridge

forward-time

Shows the time that the bridge is in the listening mode when changing from

the blocking mode to the learning mode

hello-time

Shows the time after which the bridge sends configuration frames (BPDUs)

Shows the ID of the bridge

max-age

Shows the maximum age of the data packet after which it is deleted

protocol

Shows the protocol used

priority

Shows the priority of the bridge

detail

Shows detailed information about the spanning tree settings of the interface

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands