manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Network protocols 

 

7.3 DHCP server 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

311

 

Result  

The ID of the addressed IPv4 address band is configured. 
You are now in the DHCPPOOL Configuration mode. 
The command prompt is as follows: 

cli(config-dhcp-pool-<ID>)#

 

Further notes 

You exit the DHCPPOOL configuration mode with the 

exit

 command. 

You delete the entry with the 

no ip dhcp-server pool

 command. 

7.3.2.6

 

no ip dhcp-server pool 

 

 

Note 
The command is only available with the following device: 

•

 

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 

(US version)) 

•

 

SCALANCE W761-1 RJ45 in access point mode (article number): 6GK5761-1FC00-0AA0 

and 6GK5761-1FC00-0AB0 (US version)) 

 

Description 

With this command, you delete the required IPv4 address band.  

Requirement 

You are in the Global Configuration mode. 
The command prompt is as follows: 

cli(config)#

 

Syntax 

Call up the command with the following parameters: 

no ip dhcp-server pool <pool-id (1-5)>

 

The parameter has the following meaning: 

 

Parameter 

Description 

Range of values / note 

pool-id

 

ID of the addressed IPv4 address band 

1 ... 5 
Only ID = 1 is supported. 

Result  

The required IPv4 address band is deleted. 

Further notes 

You create the IPv4 address band with the 

ip dhcp-server pool

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

LAPLACE INSTRUMENTS RF300 User Manual preview
RF300
Brand: LAPLACE INSTRUMENTS Pages: 21
LAPLACE INSTRUMENTS RF300 Mk II-A User Manual preview
RF300 Mk II-A
Brand: LAPLACE INSTRUMENTS Pages: 32
Winegard Movin' View MV-0500 Owner'S Manual preview
Movin' View MV-0500
Brand: Winegard Pages: 12
Iridium Pilot TPIM1301 Installation Manual preview
Pilot TPIM1301
Brand: Iridium Pages: 70
Kathrein AVH 06 Manual preview
AVH 06
Brand: Kathrein Pages: 4
Ubiquiti AP-5AC-90-HD Air Prism Quick Start Manual preview
AP-5AC-90-HD Air Prism
Brand: Ubiquiti Pages: 12
KING DISH Tailgater Pro VQ4900 Owner'S Manual preview
DISH Tailgater Pro VQ4900
Brand: KING Pages: 32
Maco Antennas M106C Assembly Instructions Manual preview
M106C
Brand: Maco Antennas Pages: 9
Maco Antennas M103C Assembly Instructions Manual preview
M103C
Brand: Maco Antennas Pages: 9
SLX 27801RG User Manual preview
27801RG
Brand: SLX Pages: 2
Mohu Leaf 50 Instruction Manual preview
Leaf 50
Brand: Mohu Pages: 9
Paradigm GX Connect180 Installation Manual preview
GX Connect180
Brand: Paradigm Pages: 26
EARDATEK KINGSAT P6 Quick Installation preview
KINGSAT P6
Brand: EARDATEK Pages: 92
Vislink Mantis Motorised MSAT ACU User Manual preview
Mantis Motorised MSAT ACU
Brand: Vislink Pages: 60
Hy-Gain DX-88 Instruction Manual preview
DX-88
Brand: Hy-Gain Pages: 30
Labgear LABGT12K User Manual preview
LABGT12K
Brand: Labgear Pages: 2
TENNADYNE TD Series Manual preview
TD Series
Brand: TENNADYNE Pages: 6
Labgear LABHG48A User Manual preview
LABHG48A
Brand: Labgear Pages: 2

Brands by name

Popular brands

Load more brands