manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

210

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

6.1.6.4

 

no vap broadcast ssid (access point) 

Description  

With this command, you disable the "Broadcast SSID" function. The SSID is no longer sent 

in the frame of the access point. This means that the SSID is not visible for other 

SCALANCE W700 devices. Only stations that know the SSID of the access point and that 

are configured with it can connect to the access point. The "Any SSID" option must be 

disabled on these clients. 

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

You are in the Interface Configuration mode of the VAP interface. 
The command prompt is as follows:  

cli (config-if-vapX-0-Y)#

 

Syntax 

Call the command without parameter assignment: 

no vap broadcast ssid

 

Result  

The function is disabled. 

Further notes 

You display the setting with the 

show wlan vap <vap X 0/Y>

command.  

You enable the function with the 

vap broadcast ssid

 command (default setting). 

See also 

vap broadcast ssid (access point) (Page 209) 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Directive Systems & Engineering DSE3311LYRMK Assembly Instructions preview
DSE3311LYRMK
Brand: Directive Systems & Engineering Pages: 5
Winegard Carryout G2+ Instruction Manual preview
Carryout G2+
Brand: Winegard Pages: 8
Q-Mac TA-90 Technical Manual preview
TA-90
Brand: Q-Mac Pages: 21
King-Dome 9754-LP Installation And Operating Instructions Manual preview
9754-LP
Brand: King-Dome Pages: 40
Honeywell Home AlarmNet CELL-ANTHB Installation And Setup Manual preview
AlarmNet CELL-ANTHB
Brand: Honeywell Home Pages: 2
Ciro Mazzoni I3VHF LOOP ANTENNA Instruction Manual preview
I3VHF LOOP ANTENNA
Brand: Ciro Mazzoni Pages: 126
Audio Technica ATW-A62P Installation And Operation preview
ATW-A62P
Brand: Audio Technica Pages: 4
APLIC 20180619DG006 User Manual preview
20180619DG006
Brand: APLIC Pages: 20
APLIC 303340/20191008DG006 User Manual preview
303340/20191008DG006
Brand: APLIC Pages: 24
WiMo Ultra Beam YAGI 2 Manual preview
Ultra Beam YAGI 2
Brand: WiMo Pages: 11
Televes DINOVA BOSS User Manual preview
DINOVA BOSS
Brand: Televes Pages: 24
Redline Communications AN 80i Manual preview
AN 80i
Brand: Redline Communications Pages: 8
TracVision C3 Installation Manual preview
C3
Brand: TracVision Pages: 24
SABINE SWA4U ANTENNA DIVIDER Operating Manual preview
SWA4U ANTENNA DIVIDER
Brand: SABINE Pages: 7
Aerohive Networks Aerohive AP141 Installation Manual preview
Aerohive AP141
Brand: Aerohive Networks Pages: 4
Palomar CMNF-500 Manual preview
CMNF-500
Brand: Palomar Pages: 8
NoCable 70 Manual preview
70
Brand: NoCable Pages: 6
Ramsey Electronics DA-160 Use Manual preview
DA-160
Brand: Ramsey Electronics Pages: 16

Brands by name

Popular brands

Load more brands