Siemens SIMATIC NET Page 82 Configuration Manual Download

Page: 82 / 464

Configuration

3.4 Configuration Save & Restore

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

3.4

Configuration Save & Restore

This section describes commands for displaying, saving and restoring configuration settings.

3.4.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

3.4.1.1

show running-config

Description

This command shows configuration settings of the device.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show running-config

[{

interface

{

<interface-type><interface-id>|

vlan<vlan-id(1-4094)>

ssh|ssl|acl|ip|snmp|radius|sntp|http|locked-port|

auto-logout|time|

ntp|auto-save|wlan

}][all]

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands