manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.3 Spanning Tree 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

268

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

 

 

Note 
Configure multiple properties 
With each call of the command, you can configure precisely one property. 

If you want to configure several properties, call the command several times. 

 

Result  

The selected setting was reset to the default value. 

Further notes 

You configure the setting with the 

spanning-tree

 command (properties). 

You display these settings and other information with the commands that start with 

show 

spanning tree ...

. 

6.3.4.3

 

spanning-tree auto-edge 

Description 

With this command, you enable automatic discovery of a bridge connected to the interface.   

Requirement 

You are in the Interface Configuration mode. 
The command prompt is as follows: 

cli(config-if-$$$)#

 

Syntax 

Call the command without parameters: 

spanning-tree auto-edge

 

Result  

The automatic discovery of a bridge on the interface is enabled. 

Further notes 

The automatic discovery of a bridge on the interface is disabled with the 

no spanning-tree 

auto-edge

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

MALA HDR Series User Manual preview
HDR Series
Brand: MALA Pages: 16
cahors MINISAT User Manual preview
MINISAT
Brand: cahors Pages: 50
Feig Electronic OBID ID ANT.BS.100-A Installation Manual preview
OBID ID ANT.BS.100-A
Brand: Feig Electronic Pages: 11
Camos CSA-130P Instruction Manual preview
CSA-130P
Brand: Camos Pages: 75
l-com HG2415Y Installation Instructions preview
HG2415Y
Brand: l-com Pages: 2
Yaesu G-2000RC Instruction Manual preview
G-2000RC
Brand: Yaesu Pages: 16
HiBoost C27-5S-BTW User Manual preview
C27-5S-BTW
Brand: HiBoost Pages: 15
Parsec Technologies Beagle G Installation Instructions Manual preview
Beagle G
Brand: Parsec Technologies Pages: 17
Sirio Antenne SMA 55-550 Installation Manual preview
SMA 55-550
Brand: Sirio Antenne Pages: 2
NACD IPGUARD MD-ANT345G Quick Start Manual preview
IPGUARD MD-ANT345G
Brand: NACD Pages: 5
APM AGO-250710 Specification Sheet preview
AGO-250710
Brand: APM Pages: 3
Diamond Antenna A430S10 Quick Manual preview
A430S10
Brand: Diamond Antenna Pages: 2
Maco Antennas M105HV Assembly Instructions Manual preview
M105HV
Brand: Maco Antennas Pages: 9
KVH Industries TracVision R4 Installation And Operation Instructions Manual preview
TracVision R4
Brand: KVH Industries Pages: 13
Megasat DVB-T 20 User Manual preview
DVB-T 20
Brand: Megasat Pages: 2
Megasat 1500181 User Manual preview
1500181
Brand: Megasat Pages: 29
Megasat 1500082 User Manual preview
1500082
Brand: Megasat Pages: 68
ESCO Technologies ETS-Lindgren 3106B User Manual preview
ETS-Lindgren 3106B
Brand: ESCO Technologies Pages: 79

Brands by name

Popular brands

Load more brands