manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Network structures 

 

6.3 Spanning Tree 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

277

 

6.3.5.2

 

no instance 

Description 

With this command, you cancel the assignment of a VLAN to an MST instance or delete the 

MST instance.  

Requirement 

You are in the MSTP Configuration mode. 
The command prompt is as follows: 

cli(config-mst)#

 

Syntax 

Call up the command with the following parameters: 

no instance <instance-id (1-64)> [vlan <vlan-range>]

 

The parameters have the following meaning: 

 

Parameter 

Description 

Range of values / note 

instance-id

 

Number of the MST instance 

1 ... 64 

vlan

 

Keyword for a VLAN connection 

- 

vlan-range

 

Range of VLANs that will be deleted 

from the instance 

enter the range limts with a hy-

phen or blank  

If you specify a VLAN or a VLAN range, the assignment to an MST instance is canceled. 
If you do not specify a VLAN, the MST instance is deleted. 

Result  

The assignment of a VLAN to an MST instance is canceled or the MST instance is deleted. 

Further notes 

You assign a VLAN to an MST instance with the 

instance

 command. 

You display this setting and other information with the 

show spanning-tree mst 

configuration

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Ubiquiti AirMax AMY-9M16 Quick Start Manual preview
AirMax AMY-9M16
Brand: Ubiquiti Pages: 16
RCA ANT1650R Limited Warranty preview
ANT1650R
Brand: RCA Pages: 2
Ubiquiti AF-5G30-S45 Quick Start Manual preview
AF-5G30-S45
Brand: Ubiquiti Pages: 24
Jaybeam Wireless 5121100 Installation Manual preview
5121100
Brand: Jaybeam Wireless Pages: 20
PRO.SIS.TEL. PST-20VF Assembling Instructions preview
PST-20VF
Brand: PRO.SIS.TEL. Pages: 3
Extreme Networks WS-AP3801i Quick Reference preview
WS-AP3801i
Brand: Extreme Networks Pages: 6
Mohu curve 30 Instruction Manual preview
curve 30
Brand: Mohu Pages: 2
Lab-T LavvieBeacon User Manual preview
LavvieBeacon
Brand: Lab-T Pages: 4
Labgear LAB350W User Manual preview
LAB350W
Brand: Labgear Pages: 2
Aerohive Networks Aerohive AP141 Hardware Reference Manual preview
Aerohive AP141
Brand: Aerohive Networks Pages: 111
Mohu Leaf 30 Instruction Manual preview
Leaf 30
Brand: Mohu Pages: 10
Wandy 2R Manual preview
2R
Brand: Wandy Pages: 42
Panorama Antennas DMM4-6-60 Installation Instructions Manual preview
DMM4-6-60
Brand: Panorama Antennas Pages: 8
Konig KN-DVBT-IN61L Manual preview
KN-DVBT-IN61L
Brand: Konig Pages: 51
BAS BAS-1348 OMNI 2.0 Quick User Manual preview
BAS-1348 OMNI 2.0
Brand: BAS Pages: 2
IFM CR3132 Operating Instructions Manual preview
CR3132
Brand: IFM Pages: 22
BAS REMO BAS VEGA Quick User Manual preview
REMO BAS VEGA
Brand: BAS Pages: 2
Mercury 120 525UK User Manual preview
120 525UK
Brand: Mercury Pages: 2

Brands by name

Popular brands

Load more brands