manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Network structures 

 

6.1 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

145

 

6.1.1.15

 

show wlan statistics 

Description 

This command shows the following statistics. 

●

 

how many bad frames were received or sent per WLAN interface. 

●

 

how many frames were sent per VAP interface. 

●

 

how many frames were received per VAP interface. 

In access point mode, the following additional statistics are available: 

●

 

how many frames in response to logging on or logging off were counted per VAP 

interface 

●

 

how many requesting frames for logging on or logging off were counted per VAP interface 

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call up the command with the following parameters: 

show wlan statistics <wlan 0/X>

 

The parameter has the following meaning: 

 

Parameter 

Description 

Range of values / note 

wlan 0/X

 

WLAN interface 

Enter a valid interface. 

For information on identifiers of addresses and interfaces, refer to the section "Interface 

identifiers and addresses (Page 25)". 

Result  

The statistics are displayed for the selected WLAN interface. The range depends on the 

selected operating mode. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Feig Electronic ID ANT.U580/290-FCC Installation Instructions Manual preview
ID ANT.U580/290-FCC
Brand: Feig Electronic Pages: 11
Huawei AAU3940 Hardware Maintenance Manual preview
AAU3940
Brand: Huawei Pages: 25
Huawei D602 Manual To The Installation preview
D602
Brand: Huawei Pages: 2
Huawei RTN 360 V100 Quick Installation Manual preview
RTN 360 V100
Brand: Huawei Pages: 13
Huawei Straight Talk H258C User Manual preview
Straight Talk H258C
Brand: Huawei Pages: 22
NETGEAR ANT2407 - PROSAFE Indoor 7 dBi Omni-directional Antenna Installation Manual preview
ANT2407 - PROSAFE Indoor 7 dBi Omni-directional Antenna
Brand: NETGEAR Pages: 2
NETGEAR Orbi RBS50Y User Manual preview
Orbi RBS50Y
Brand: NETGEAR Pages: 35
Hemisphere GPS Crescent A100 User Manual preview
Crescent A100
Brand: Hemisphere GPS Pages: 44
Hemisphere GPS C321 User Manual preview
C321
Brand: Hemisphere GPS Pages: 59
Winegard RoadTrip SD Installation Manual preview
RoadTrip SD
Brand: Winegard Pages: 8
RCA ANT501 - TV / Radio Antenna User Manual preview
ANT501 - TV / Radio Antenna
Brand: RCA Pages: 2
RCA ANT711 Instruction Manual preview
ANT711
Brand: RCA Pages: 5
Cabletech ANT0640 User Manual preview
ANT0640
Brand: Cabletech Pages: 12
Cabletech ANT0690 User Manual preview
ANT0690
Brand: Cabletech Pages: 20
EAntenna 17800.06-10 Manual preview
17800.06-10
Brand: EAntenna Pages: 22
Steren ANT-5000 Instruction Manual preview
ANT-5000
Brand: Steren Pages: 2
H3C ANT-2503C-M6 Installation Manual preview
ANT-2503C-M6
Brand: H3C Pages: 9
A.H. Systems AK-26G Operation Manual preview
AK-26G
Brand: A.H. Systems Pages: 10

Brands by name

Popular brands

Load more brands