manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Network structures 

 

6.1 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

197

 

6.1.5.46

 

wlan guard interval (access point) 

Description    

With this command, you specify the send pause that must be kept to between two 

transferred OFDM symbols. 

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

●

 

The IEEE 802.11n transmission standard is enabled. 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan guard interval { GI400 | GI800 }

 

The parameters have the following meaning: 

 

Parameters 

Description 

GI400

 

The send pause is 400 ns (default) 

GI800

 

The send pause is 800 ns 

Result  

The function is enabled and the send pause set. 

Further notes 

You display the setting with the 

show wlan advanced-11n <wlan 0/X>

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Feig Electronic OBID ID ISC.ANT340/240-A Installation Manual preview
OBID ID ISC.ANT340/240-A
Brand: Feig Electronic Pages: 28
Javad TRIUMPH-1M Plus User Manual preview
TRIUMPH-1M Plus
Brand: Javad Pages: 26
MELICONI AT38 PLUS User Instructions preview
AT38 PLUS
Brand: MELICONI Pages: 28
Feig Electronic ID ANT.U580/290-FCC Installation Instructions Manual preview
ID ANT.U580/290-FCC
Brand: Feig Electronic Pages: 11
KVH Industries TracVision TV5 Installation Manual preview
TracVision TV5
Brand: KVH Industries Pages: 46
RFI FSA20-41-DIN Installation preview
FSA20-41-DIN
Brand: RFI Pages: 4
TRENDnet TEW-OA08OK Datasheet preview
TEW-OA08OK
Brand: TRENDnet Pages: 2
Furuno FELCOM 15 Operator'S Manual preview
FELCOM 15
Brand: Furuno Pages: 210
Beam RST720 Installation Manual preview
RST720
Brand: Beam Pages: 2
Beam RST700 Installation Manual preview
RST700
Brand: Beam Pages: 2
Beam RST701 Installation Manual preview
RST701
Brand: Beam Pages: 2
Beam RST705 Installation Manual preview
RST705
Brand: Beam Pages: 2
Beam MG200-VAB Installation Manual preview
MG200-VAB
Brand: Beam Pages: 2
Hughes 9211 User Manual preview
9211
Brand: Hughes Pages: 80
CreatComm TB8H User Manual preview
TB8H
Brand: CreatComm Pages: 36
Sirio Antenne CX 4m series Installation Manual preview
CX 4m series
Brand: Sirio Antenne Pages: 2
CommScope ION-M8P S Manual preview
ION-M8P S
Brand: CommScope Pages: 42
Icom AH-2b Instruction Manual preview
AH-2b
Brand: Icom Pages: 8

Brands by name

Popular brands

Load more brands