Siemens SIMATIC NET Page 220 Configuration Manual Download

Page: 220 / 464

Network structures

6.2 VLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

220

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

show mac-address-table dynamic unicast[vlan<vlan-range>]

[address<aa:aa:aa:aa:aa:aa>][{interface<interface-type>

<interface-id>}]

The parameters have the following meaning:

Parameter

Description

Range of values / note

vlan

Keyword for a VLAN or VLAN range

vlan-range

Number of the addressed VLAN or VLAN range

1 ... 4094

address

Keyword for a MAC address

aa:aa:aa:aa:aa:aa

MAC address

interface

Keyword for a an interface description

interface-type

Type or speed of the interface

Enter a valid interface.

interface-id

Module no. and port no. of the interface

For information on names of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".
If you do not select any parameter from the parameter list, the entries are displayed for all

available interfaces.

Result

The entries are displayed.

6.2.1.5

show vlan

Description

This command shows the specific information for all or a selected VLAN.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands