manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Security and authentication 

 

10.3 Management Access Control List 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

428

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

10.2.5.11

 

no vap communication with ethernet (access point) 

Description    

With this command, you specify that the client cannot communicate via the Ethernet 

interface. 

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

You are in the Interface Configuration mode of the VAP interface. 
The command prompt is as follows:  

cli (config-if-vapX-0-Y)#

 

Syntax 

Call the command without parameter assignment: 

no vap communication with ethernet

 

Result  

The communication option is disabled.  

Further notes 

You display the settings with the 

show wlan security <vapX 0/Y>

 command.  

You enable the function with the 

vap communication with ethernet

 command. 

See also 

vap communication with ethernet (access point) (Page 427) 
 

10.3

 

Management Access Control List 

This section describes the commands relevant for working with the management access 

control list. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

DAPAudio EDGE EUA-1 Manual preview
EDGE EUA-1
Brand: DAPAudio Pages: 16
Alpha Delta DX-CC Installation Notes preview
DX-CC
Brand: Alpha Delta Pages: 4
Matchmaster 02MM-GX400 Manual preview
02MM-GX400
Brand: Matchmaster Pages: 2
Philips SDV2950 User Manual preview
SDV2950
Brand: Philips Pages: 24
Sea Tel Base Exit Quick Start Manual preview
Base Exit
Brand: Sea Tel Pages: 10
NETGEAR 2409 Installation Manual preview
2409
Brand: NETGEAR Pages: 26
Sirio Antenne CX Series Installation Manual preview
CX Series
Brand: Sirio Antenne Pages: 2
RCA VH126N (Spanish) Manual Del Usuario preview
VH126N
Brand: RCA Pages: 5
Televes 144401 User Manual preview
144401
Brand: Televes Pages: 32
Steren ANT-XTREME 0817A Instruction Manual preview
ANT-XTREME 0817A
Brand: Steren Pages: 2
Steren COM-835 User Manual preview
COM-835
Brand: Steren Pages: 8
M2 Antenna Systems 20M5-125 Manual preview
20M5-125
Brand: M2 Antenna Systems Pages: 10
A.H. Systems AK-26G Operation Manual preview
AK-26G
Brand: A.H. Systems Pages: 10
Hawking HAI8DD Specifications preview
HAI8DD
Brand: Hawking Pages: 2
ADC Digivance CXD Operation Manual preview
Digivance CXD
Brand: ADC Pages: 74
Oehlbach Flat Style One User Manual preview
Flat Style One
Brand: Oehlbach Pages: 40
Kathrein BAS 62 Manual preview
BAS 62
Brand: Kathrein Pages: 48
CG Antenna GW-1000 User Manual preview
GW-1000
Brand: CG Antenna Pages: 15

Brands by name

Popular brands

Load more brands