Siemens SIMATIC NET Page 341 Configuration Manual Download

Page: 341 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

341

Syntax

Call up the command with the following parameters:

no snmp group <GroupName> user <UserName>security-model{v1|v2c|v3}

The parameters have the following meaning:

Parameter

Description

Range of values / note

GroupName

Name of the group

max. 32 characters

user

Keyword for the user name

UserName

Name of the user

max. 32 characters

security-model

Specifies which security settings are

used for sending

•

v2c

•

Result

The details of the group are deleted.

Further notes

You change the details of an SNMP group with the

snmp group

command.

You display the created SNMP groups with the

show snmp group

command.

You display the created SNMP user with the

show snmp user

command.

7.4.2.12

snmp notify

Description

With this command, you configure the details of the SNMP notifications.

Requirement

You are in the Global configuration mode.
The command prompt is as follows:

cli(config)#

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands