manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

194

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

6.1.5.43

 

wlan fragmentation threshold 

Description  

With this command, you specify the maximum packet size transferred on the wireless link. 

Large packets are divided up into small packets prior to transmission and then reassembled 

into the original size after they have been received. 

Requirement 

●

 

The transmission standard 802.11g or 802.11a is set. 

●

 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan fragmentation threshold <bytes(256-2346)>

 

 The parameter has the following meaning: 

 

Parameters 

Description 

Range of values / note 

bytes

 

Packet size in bytes 

256...2346 

Default: 2346 

Result  

The packet size is specified. 

Further notes 

You configure the transmission standard with the 

wlan mode

 command. 

You display the setting with the 

show wlan advanced

 

<wlan 0/X>

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

M2 Antenna Systems 7-10-30LP8 UP-KIT Manual preview
7-10-30LP8 UP-KIT
Brand: M2 Antenna Systems Pages: 6
Matchmaster 02MM-GX400 Manual preview
02MM-GX400
Brand: Matchmaster Pages: 2
Altelix AS6G17B65M4-A5C Assembly Instructions preview
AS6G17B65M4-A5C
Brand: Altelix Pages: 3
Feig Electronic OBID i-scan ID ISC.ANT.U600/270 FCC Installation Manual preview
OBID i-scan ID ISC.ANT.U600/270 FCC
Brand: Feig Electronic Pages: 23
Bode 907 970 Installation Manual preview
907 970
Brand: Bode Pages: 3
MaxRange Value Assembly Instructions Manual preview
Value
Brand: MaxRange Pages: 7
UltraPro Flat Panel User Manual preview
Flat Panel
Brand: UltraPro Pages: 2
Sea Tel 9711QOR-86 Installation And Operation Manual preview
9711QOR-86
Brand: Sea Tel Pages: 243
DirecTV TRKS26 Installation Manual preview
TRKS26
Brand: DirecTV Pages: 1
Hemisphere GPS Crescent A100 User Manual preview
Crescent A100
Brand: Hemisphere GPS Pages: 44
Hemisphere GPS C321 User Manual preview
C321
Brand: Hemisphere GPS Pages: 59
Diamond Antenna KV2 Operation Instructions preview
KV2
Brand: Diamond Antenna Pages: 3
Diamond Antenna CPVU8 Operation Instructions preview
CPVU8
Brand: Diamond Antenna Pages: 4
ETS-Lindgren 3184 Quick Start Manual preview
3184
Brand: ETS-Lindgren Pages: 8
ETS-Lindgren BiConiLog 3142C User Manual preview
BiConiLog 3142C
Brand: ETS-Lindgren Pages: 29
Winegard SK-3003 Operation Manual preview
SK-3003
Brand: Winegard Pages: 5
ZCG Yagi Y300 Series Installation Manual preview
Yagi Y300 Series
Brand: ZCG Pages: 3
Hy-Gain AV-18HT Instruction Manual preview
AV-18HT
Brand: Hy-Gain Pages: 36

Brands by name

Popular brands

Load more brands