Rhymebus RM6F5 series Operation Manual Download Page 122

Page: 122 / 195

Chapter 6 Parameter Description of Pump

122

6-9 Overheating Disposals

Func.

Name

Description

F_140

NTC Thermistor
Setting

=0: Disable.

*Disable the NTC thermistor.
*The

―Ht‖ fault detection is disabled.

*The display 6 (terminal status and heat sink temperature) of

drive monitor mode will not display heat sink

’s temperature.

=1: Enable.

*Enable the NTC thermistor.

F_141

Drive Overheat
Pre-alarm
Selection

=0: Disable.
=1: Warning (Ht):

*Continue operation.

=2: Warning (Ht):

*Drive automatically de-rates the switching frequency every 5

minutes.

=3: Warning (Ht):

Drive trips to ―Ht‖ protection and stop the drive operation,

when the temperature of heat sink is over F_142.

*The cooling fan will restart, when the temperature is lower

than the drive overheating dead band (F_143).

F_142

Drive Overheat
Pre-alarm Level

․

Set the warning level for overheating detection.

F_143

Drive Overheating
Dead Band

․

Set the temperature dead band of F_142 and F_145.

F_144

Fan Control
Selection

=0: Forced air.

*Fan will start running at drive power ON.

=1: Operation air.

*Fan will start running when the drive is running.

=2: Temperature level setting

*Fan will start running when the temperature is over the setting

level of F_145.

F_145

Temperature Level
of Fan Activation

․

Set the temperature level of fan activation.

F_146

Minimum Operation
Time of Fan

․

Set the minimum operation time for fan when the fan

stops.

Display ”Ht”

Minimum

operation

time F_146

Drive

overheating

pre-alarm level

F_142

Temperature

level of fan

activation F_145

Fan operation

Overheating

pre-alarm level

※

F_144 = 2 (Temperature Level setting)

Temperature

Time

105

℃

Display

”OH”

Overheating

dead band

F_143

Overheating

dead band

F_143

Overheating

dead band

F_143

Overheating

pre-alarm level

Time

Summary of Contents for RM6F5 series




































































































































































































Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands

Rhymebus RM6F5 series, Operation Manual

Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands