Rhymebus RM6F5 series Operation Manual Download Page 149

Page: 149 / 195

Chapter 8 Operation Procedures and Fault Protection

149

Display

Description

Cause

Troubleshooting

(dtF)

MAIN

RUNNING

Direction
command error

Forward and reverse
commands are
inputted to the drive
simultaneously

Check the direction
command.

(Wr_F)

MAIN

RUNNING

Different
software version
inter-copy

The software version
of drive is different.

Check up the
software version.

(OP)

KEYPAD

Running

Over pressure

●Over pressure
level: F_148
●Detect time of
over pressure:
F_149

●The setting value of

F148 is not
appropriate.

●Pump oulet

pressure is too
high.

●The water valve

shut down
immediately.

●The pressure
sensor is abnormal.

●Check the settings

of function

(F_148~F149)

●Check the pressure

of pump system and
water pipes.

(CPyF)

KEYPAD

Running

Parameter copy
fault

● In the parallel
control, the software
version of auxiliary
drive do not
correspond with the
host drive.

● The software
version of auxiliary
drives must be
correspond with the
host drive.

Summary of Contents for RM6F5 series




































































































































































































Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands

Rhymebus RM6F5 series, Operation Manual

Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands