Rhymebus RM6F5 series Operation Manual Download Page 76

Page: 76 / 195

Chapter 5 Parameter Setting Description

F_003

Selection of ―STOP‖ Key Validity

a. F_003=0

When the start command by terminal, the ―

STOP

RESET

‖ key of keypad disabled.

b. F_003=1

When the start command by terminal, the ―

STOP

RESET

‖ key of keypad enabled.

c. The

applications of “STOP” key.

(I). Emergency stop:

When the start and frequency command are both controlled by multi-function input

terminal (F_001=0 or 1), the output frequency will be decreased to 0Hz and

displaying

on keypad

by pressing ―

STOP

RESET

‖ key during operation.

If the drive needs to be restarted, cut off the wire between the terminals of the start

command (FWD or REV) and COM and restart the drive again.

(II). Normal stop:

F_001=2 or 3, the start command by ―

‖ key of keypad KP-201C and the stop is

controlled by

―

STOP

RESET

‖

key.

F_004

Setting Value (SV) Change Selection

a. F_004=0

In the monitor mode, the setting value cannot be changed by KP-605 keypad to avoid
possible mistakes and errors.

b. F_004=1

In the monitor mode, the setting value can be changed by KP-605 keypad.

F_005

Setting Value (SV) Auto-Storing

a. F_005=0

In the monitor mode, the setting value will not be saved automatically.

b. F_005=1

In the monitor mode, the setting value will be saved automatically after 3 minutes.

Summary of Contents for RM6F5 series




































































































































































































Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands

Rhymebus RM6F5 series, Operation Manual

Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands