Rhymebus RM6F5 series Operation Manual Download Page 148

Page: 148 / 195

Chapter 8 Communication Description

148

Warning Messages of Drive

*When the drive displays below messages, drive stops output. If the abnormal

condition is removed, the drive auto recovers the normal operation.

Display

Description

Cause

Troubleshooting

(LE)

KEYPAD

Running

Power source
under voltage

The internal DC
bus voltage level
is below 70%.

The voltage of power
source is too low.

Check if the voltage of
power source is valid.

(bb)

KEYPAD

Running

Drive output
interruption

Drive stops the
output when the
output interruption
command is
activated.

Clear drive output
interruption
command.

(Fr)

KEYPAD

Running

Coast to stop

Drive stops the
output when the
coast to stop
command is
activated.

Clear ―coast to stop‖
command.

(db)

KEYPAD

Running

Dynamic brake
over voltage

The internal DC
bus voltage of
drive is over the
protection level.

DC bus voltage is
too high .

Increase the
―deceleration time‖ or
use high torque
braking method and
add dynamic brake
unit.

(PrEr)

KEYPAD

Running

Program fault

－－－

Check the software
version of drive.

(Ht)

KEYPAD

Running

Drive
overheating

●The temperature

of drive

’s heat

sink reaches the
warning level.

●Warning level:

F_142.

●The surrounding

temperature is too
high.

●The heat sink has

foreign body.

●The cooling fan of

drive is fault.

●Improve the system

ventilation.

●Clean the dust on

the heat sink.

●Return the drive to

replace the cooling
fan.

(Err_00)

KEYPAD

Running

(Err_01)

KEYPAD

Running

Err_00: Keypad
cable trip before
connecting

Err_01: Keypad
cable trip during
operation

●The connecting

wire of the keypad
is loose.

●The keypad jack of

the drive is
oxidized.

Check the wire
between the keypad
and drive.

Summary of Contents for RM6F5 series




































































































































































































Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands

Rhymebus RM6F5 series, Operation Manual

Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands