manualshive.com logo in svg

Rhymebus RM6F5 series, Operation Manual

The Rhymebus RM6F5 Operation Manual is a comprehensive guide designed to assist users in understanding and operating their RM6F5 series product effortlessly. With its user-friendly interface, this manual is available for free download, allowing users to access it conveniently at manualshive.com. Enhanced product experience starts here!

Share
Download
background image

 

 

Chapter 1    Cautions Before Installation

 -------------------------------- 11

 

1-1 Product Verification -------------------------------------------------------------------------- 11

 

1-1-1 Confirmation of Appearance ------------------------------------------------------ 11

 

1-1-2 The description of nomenclature: ----------------------------------------------- 11

 

1-1-3 Confirmation of Accessories ------------------------------------------------------ 12

 

1-2 Standard Specifications -------------------------------------------------------------------- 12

 

1-2-1 Three-Phase 200V Series --------------------------------------------------------- 12

 

1-2-2 Three-Phase 400V Series --------------------------------------------------------- 14

 

1-3 Common Specifications -------------------------------------------------------------------- 16

 

1-3-1 The Features of Control and Operation---------------------------------------- 16

 

Chapter 2    Installation and Confirmation

 ------------------------------ 19

 

2-1 Basic Equipment ----------------------------------------------------------------------------- 19

 

2-2 Installing the Drive --------------------------------------------------------------------------- 19

 

2-3 Descriptions of Terminal and Wiring Diagram ---------------------------------------- 23

 

2-4 Wiring Diagram and Setting for Single-pump and Multi-pump Applications -- 40

 

2-4-1 Single Pump Control ---------------------------------------------------------------- 40

 

2-4-2 Dual & Multi-pump Control (E-mode

、

F-mode

、

M-mode) --------------- 41

 

2-4-3 Multi-pump Use of ACE-S12 Signal Distributor Control ------------------- 44

 

2-4-4 Multi-pump Control (S-mode Application) ------------------------------------- 45

 

Chapter 3    The Setting of Keypad

 ----------------------------------------- 46

 

3-1 Functions of Keypad (KP-605) ----------------------------------------------------------- 46

 

 --------------------------------------------------------------------------------------------------------- 46

 

3-2 The Operation of Keypad(KP-605) and Monitor Mode ----------------------------- 48

 

Chapter 4    Parameter List

 ----------------------------------------------------- 55

 

Chapter 5    Parameter Setting Description

 ---------------------------- 71

 

5-1 The Keypad Setup --------------------------------------------------------------------------- 71

 

5-2 Preset Speed Setup ------------------------------------------------------------------------- 78

 

5-3 Multi-Speed Accel./Decel. Time Setup ------------------------------------------------- 80

 

5-4 V/F Pattern Setup ---------------------------------------------------------------------------- 82

 

5-5 Analog Input Command Setup ------------------------------------------------------------ 84

 

5-6 Analog Output Setup ------------------------------------------------------------------------ 87

 

5-7 Motor Protecti Primary Frequency on Setup ------------------------------------------ 89

 

5-8 Multi-Function Input Setup ----------------------------------------------------------------- 90

 

5-9 Multi-Function Output Setup -------------------------------------------------------------- 94

 

5-10 Automatic Torque Compensation ------------------------------------------------------- 97

 

5-11 System Overload Detection SetUp ---------------------------------------------------- 98

 

5-12 Stall Prevention SetUp -------------------------------------------------------------------- 99

 

5-13 DC Braking Set Up ----------------------------------------------------------------------- 100

 

5-14 Operation Selection at Instantaneous Power Failure --------------------------- 100

 

5-15 Speed Tracing ----------------------------------------------------------------------------- 101

 

5-16 Current Limitation ------------------------------------------------------------------------ 101

 

5-17 Others Function --------------------------------------------------------------------------- 102

 

6. Parameter Description of Pump

 --------------------------------------- 104

 

Table of Contents 

 

Summary of Contents for RM6F5 series




































































































































































































Reviews:

No comments

Related manuals for RM6F5 series

ABB FEPL-02 Ethernet POWERLINK Quick Installation And Start-Up Manual preview
FEPL-02 Ethernet POWERLINK
Brand: ABB Pages: 2
ABB FENA-01 Quick Installation And Start-Up Manual preview
FENA-01
Brand: ABB Pages: 2
Wasp B2000 Installation Manual preview
B2000
Brand: Wasp Pages: 16
Saitek P880 User Manual preview
P880
Brand: Saitek Pages: 44
Eaton SC100 Operation Handbook preview
SC100
Brand: Eaton Pages: 86
CALEFFI 543 Series Quick Start Manual preview
543 Series
Brand: CALEFFI Pages: 2
CALEFFI 5350 Series Manual preview
5350 Series
Brand: CALEFFI Pages: 12
Caliber RC20 User Manual preview
RC20
Brand: Caliber Pages: 6
Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Brand: Danfoss Pages: 124
Danfoss AME 55 Installation Manual preview
AME 55
Brand: Danfoss Pages: 2
Danfoss AME 110 NL Datasheet preview
AME 110 NL
Brand: Danfoss Pages: 8
Danfoss AK-CH 650 User Manual preview
AK-CH 650
Brand: Danfoss Pages: 114
Danfoss ECL Comfort 300 Quick Manual preview
ECL Comfort 300
Brand: Danfoss Pages: 2
Danfoss TS715Si Installation Manual preview
TS715Si
Brand: Danfoss Pages: 16
Danfoss AME 438 SU Installation Manual preview
AME 438 SU
Brand: Danfoss Pages: 24
Danfoss AK-LM 330 User Manual preview
AK-LM 330
Brand: Danfoss Pages: 8
Danfoss ECL Comfort 296 Operating Manual preview
ECL Comfort 296
Brand: Danfoss Pages: 159
Danfoss VLT AutomationDrive FC 301 Operating Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 78

Brands by name

Popular brands

Load more brands