Rhymebus RM6F5 series Operation Manual Download Page 107

Page: 107 / 195

Chapter 5 Parameter Setting Description

107

6-2 Sequential Operation and Parallel Control of Multi-pump

․

6-2-1 Sequential Control for Multi-Pump(Only used for F-mode

、

E-mode)

Func.

Name

Description

F_013

Pump Shift Operation
(Parallel control)

=0: Disable.
=1: Shift the pump operation after the operating time

(F_024).

*The function is to shift the operation from one pump to

another when the operating time (F_024) reaches.

=2: Shift the pump operation after a drive stops.

*The function is to shift the operation from one pump to

another after an operating pump drive comes to stop.

=3: Both 1 and 2 enable.

F_024

Pump Auto Shift Time
(Parallel control)

․

Set the pump operating time of the sequential control
in multi-pump control.

*Setting range:0~240hr.
*0: Disable. (drive will not execute sequential operation.)

F_137

Delay Time at Pump
Shifting

․

The delay time setting is to remain the stable pressure
of the system at the interchanging of the pump
operation.

*Default: 10sec.
*During the pump shifting, the system pressure becomes

unstable when one pump drive disengages and another
pump drive engages. The delay time is to increase the
disengaging time of the current pump drive to stabilize the
system pressure.

1. The sequence of pump shifting for multi-pump control as below diagram.

Drive #0

Time

Drive #1

Drive #2

Drive #3

2. Below figure is the process of function F_024 and F_137.

Drive #1

Output

frequency

Actual

pressure

(PV)

Setting

pressure

(SV)

Drive #1

F_024

F_137

Drive #0

Drive #1

Drive #0

Time

Summary of Contents for RM6F5 series




































































































































































































Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands

Rhymebus RM6F5 series, Operation Manual

Search results

Summary of Contents for RM6F5 series

Reviews:

Related manuals for RM6F5 series

Brands by name

Popular brands