manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

xxv

„

Chapter 4,  System Interface Unit (SIU). Describes the modules and functions of the 
SIU, which controls system start-up and initialization as well as operation, protection, and 
the external 60x-compatible system bus.

„

Chapter 5,  Reset. Covers reset sources, causes, and configurations; gives examples of 
different reset configuration scenarios, including systems with multiple MSC8113s.

„

Chapter 6,  Boot Program. Describes the bootloader program, which loads and executes 
source code that initializes the MSC8113 after it completes a reset sequence and programs 
its registers for the required mode of operation. This chapter covers selection of 
bootloader modes, normal sequence of events for bootloading a source program, and 
booting in a multi-processor environment.

„

Chapter 7,  Clocks. Contains an overview of the MSC8113 clock module. For complete 
clock information, refer to the MSC8113 Technical Data sheet. The data sheet is available 
in PDF format on the Freescale web site listed on the back cover of this manual.

„

Chapter 8,  Memory Map. Defines the address spaces for all MSC8113 modules; includes 
cross references to all registers discussed.

„

Chapter 9,  Extended Core. Describes the structure of the extended core, which includes 
the SC140 core, its internal memory (M1), the extended QBus structure (EQBS), the 
Instruction Cache (ICache), the programmable interrupt controller (PIC), and the local 
interrupt controller (LIC).

„

Chapter 10,  MQBus and M2 Memory. Describes how the MQBus supports a multi-core 
environment by allowing all three SC140 cores to share the M2 memory through the 
MQBus. The MQBus ensures a low miss ratio for SC140 ICache accesses.

„

Chapter 11,  SQBus. Explains the structure and function of the SQBus, which is available 
to all SC140 cores to fetch program code from external memory on the system bus.

„

Chapter 12,  Memory Controller. Covers the features and basic architecture of the 
memory controller, which is part of the system interface unit (SIU). The memory 
controller provides an interface to internal DSP memory and DSP peripherals residing on 
the internal local bus and also to external memory and peripheral devices on the external 
60x-compatible system bus. In addition to features and basic architecture, this chapter 
extensively covers the three basic machines that compose the memory controller: 
synchronous DRAM machine (SDRAM), general-purpose chip-select machine (GPCM), 
and the user-programmable machines (UPMs).

„

Chapter 13,  System Bus. Discusses the system bus, which is a 60x-compatible bus that 
provides flexible support for the on-chip SC140 cores as well as other internal and 
external 60x-compatible bus masters.

„

Chapter 14,  Direct Slave Interface (DSI). Discusses the DSI host interface, which is a 
32/64-bit wide, full-duplex, double-buffered, parallel port that can directly connect to the 
data bus of a host processor. The DSI supports a variety of buses and provides glueless 
connection with a number of industry-standard microcomputers, microprocessors, and 
DSPs. 

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
Barco EX Safety Manual preview
EX
Brand: Barco Pages: 100
Jetter JXM-IO-E30 Installation Manual preview
JXM-IO-E30
Brand: Jetter Pages: 35
GAMDIAS Aura GC2 Quick Installation Manual preview
Aura GC2
Brand: GAMDIAS Pages: 15
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Brand: Jetter Pages: 67
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
Delta Electronics DTE-20T Instruction Sheet preview
DTE-20T
Brand: Delta Electronics Pages: 1
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
NC-link NC-AP111 User Manual preview
NC-AP111
Brand: NC-link Pages: 20
Cypress PSoC 4 S Series Quick Start Manual preview
PSoC 4 S Series
Brand: Cypress Pages: 4
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
AC Infinity AIRCOM Series User Manual preview
AIRCOM Series
Brand: AC Infinity Pages: 24
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Renesas H8S/2646 Series User Manual preview
H8S/2646 Series
Brand: Renesas Pages: 20
Uctronics U6180 Instruction Manual preview
U6180
Brand: Uctronics Pages: 2
Delta AH10EN-5A Series Operation Manual preview
AH10EN-5A Series
Brand: Delta Pages: 132
Advantech SNMP-1000-E2B1E How To Connect preview
SNMP-1000-E2B1E
Brand: Advantech Pages: 4

Brands by name

Popular brands

Load more brands