manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

The NXP Semiconductors MSC8113 Reference Manual is an essential resource for users of this cutting-edge product. It provides in-depth guidance on its features, functionalities, and usage. Download the manual for free from our website to maximize your understanding and optimize your experience with the MSC8113.

Share
Download
background image

Memory Controller Programming Model

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

12-99

Table 12-32 describes ORx fields in SDRAM mode. For details see Section 12.2.14, SDRAM 
Configuration Examples, on page 12-29.

Table 12-32.  ORx Bit Descriptions (SDRAM Mode)

Name

Reset

Description

Settings

SDAM

0–11

—

SDRAM Address Mask
Masks corresponding BRx bits. Masking address 
bits independently allows SDRAM devices of 
different size address ranges to be used. Clearing 
bits masks the corresponding address bit. Setting 
bits causes the corresponding address bits to be 
compared with the address lines. Address mask bits 
can be set or cleared in any order, allowing a 
resource to reside in more than one area of the 
address map. SDAM can be read or written at any 
time.
Note:

If PSDMR[PBI]=0, the maximum size of 
the memory bank should not exceed 128 
MB.

000000000000 = 4 GB

100000000000 = 2 GB

110000000000 = 1 GB

111000000000 = 512 MB

111100000000 = 256 MB

111110000000 = 128 MB

111111000000 = 64 MB

111111100000 = 32 MB

111111110000 = 16 MB

111111111000 = 8 MB

111111111100 = 4 MB

111111111110 = 2 MB

111111111111 = 1 MB

LSDAM

12–16

—

Lower SDRAM Address Mask
Note:

Reset LSDAM to 0x0 to implement a 
minimum size of 1 MB when using 
SDRAM.

SDRAM Page Information

BPD

17–18

—

Banks Per Device
Sets the number of internal banks per SDRAM 
device. Note that for 128-Mb SDRAMs, BPD must 
be 00 or 01.

00

2 internal banks per device.

01

4 internal banks per device.

10

8 internal banks per device (not 
valid for 128-Mb SDRAMs).

11

Reserved.

ROWST

19–22

—

Row Start Address Bit
Sets the demultiplexed row start address bit. The 
value of ROWST depends on PSDMR[PBI].

For PSDMR[PBI] = 0:

0010 A7

0100 A8

0110 A9

1000 A10

1010 A11

1100 A12

1110 A13 
Other values are reserved.

For PSDMR[PBI] = 1:

0000 A0

0001 A1

...

1100 A12
1101–1111 Reserved

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
NXP Semiconductors MIMXRT1160 Hardware Development Manual preview
MIMXRT1160
Brand: NXP Semiconductors Pages: 24
Intel NetStructure ZT 5515 Product Specification preview
NetStructure ZT 5515
Brand: Intel Pages: 90
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Brand: ICP DAS USA Pages: 62
Renesas E200F User Manual preview
E200F
Brand: Renesas Pages: 76
Datum bc635VME Operation And Technical Manual preview
bc635VME
Brand: Datum Pages: 49
CAME 848EA-0120 Setup And User'S Manual preview
848EA-0120
Brand: CAME Pages: 32
Waveshare High-Precision AD/DA Board User Manual preview
High-Precision AD/DA Board
Brand: Waveshare Pages: 8
ETAS ES1337.2 User Manual preview
ES1337.2
Brand: ETAS Pages: 29
SONIX MP5S Plus Writer Quick Manual preview
MP5S Plus Writer
Brand: SONIX Pages: 23
IBM 7311-D11 Removal And Replacement Procedures preview
7311-D11
Brand: IBM Pages: 74
ekwb 3831109819395 Manual preview
3831109819395
Brand: ekwb Pages: 10
LevelOne NVR-0432 User Manual preview
NVR-0432
Brand: LevelOne Pages: 142
Serial Cables PCI4-AD-x16HI-BG4 User Manual preview
PCI4-AD-x16HI-BG4
Brand: Serial Cables Pages: 15
National Instruments PXI-GPIB Getting Started preview
PXI-GPIB
Brand: National Instruments Pages: 45
Inter-m S- Media Manual preview
S- Media
Brand: Inter-m Pages: 20
BOSER Technology HS-4703 Manual preview
HS-4703
Brand: BOSER Technology Pages: 78

Brands by name

Popular brands

Load more brands