NXP Semiconductors MSC8113 Reference Manual Download Page 416 | Manualshive

Page: 416 / 1202

background image

MSC8113 Reference Manual, Rev. 0

12-108

Freescale Semiconductor

Memory Controller

Table 12-36. MxMR Bit Descriptions

Name

Reset

Description

Settings

BSEL

0

0

Bus Select
Assigns banks that select UPMx to the system
bus or local bus. UPMC is assigned to the local
bus and controls accesses to the internal
memories. UPMA and UPMB control external
devices residing on the system bus. If 60x bus
refresh is required, UPMA should be assigned
to system bus.
Note:

The boot sequence sets
MCMR[BSEL].

0

Banks that select UPMx are assigned to
the system bus.

1

Banks that select UPMx are assigned to
the local bus.

RFEN

1

0

Refresh Enable
Indicates that the UPM needs refresh services.
See the discussion of the system bus Assigned
UPM Refresh Timer (PURT) in Section 12.8.

0

Refresh services are not required.

1

Refresh services are required.

OP

2–3

00

Command Opcode
Determines the command executed by the
UPMx when a memory access hits a UPM
assigned bank.

For Write to array, on the next memory access
to a UPM assigned bank, write the contents of
the MDR into the RAM location pointed by
MAD. After the access, the MAD field is
automatically incremented.

For Read from array, on the next memory
access to a UPM assigned bank, read the
contents of the RAM location pointed by MAD
into the MDR. After the access, the MAD field is
automatically incremented.

For Run pattern, on the next memory access to
a UPM assigned bank, run the pattern written in
the RAM array. The pattern run starts at the
location pointed to by MAD and continues until
the LAST bit is set in the RAM.
Note:

RLF determines the number of times a
loop executes during a pattern run.

00 Normal

operation.

01

Write to array.

10 Read

from

array.

11 Run

pattern.

—

4

0

Reserved. Write to zero for future compatibility.

AMx

5–7

000

Address Multiplex Size
Determines how the address of the current
memory cycle can be output on the address
lines. The address output is controlled by the
contents of the UPMx RAM array. This field is
useful when the MSC8113 connects to DRAM
devices requiring row and column addresses
multiplexed on the same lines. See Section
12.4.4.3, Address Multiplexing, on page 12-59.

AMx

External

System Bus

Address Line

Signal Driven

on External

Line

000

A[16–31]

A[8–23]

001

A[16–31]

A[7–22]

010

A[16–31]

A[6–21]

011

A[16–31]

A[5–20]

100

A[17–31]

A[5–19]

101

A[18–31]

A[5–18]

«
...
414
415
416
417
418
...
»

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8113

Brand: 3Com Pages: 8

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: Alesis Pages: 46

Urban Wireless CC-VT240W

Brand: Cateye Pages: 15

Brand: Paradyne Pages: 10

Super Sound Set SR-JV80-07

Brand: Roland Pages: 8

Brand: Schrack Technik Pages: 2

Brand: Caen Pages: 14

Brand: ZALMAN Pages: 8

Brand: Compro Technology Pages: 2

Kontron SMARC-sXEL

Brand: S&T Pages: 108

Brand: Air Live Pages: 2

Brand: ICOP Technology Pages: 42

Brand: Dave Embedded Systems Pages: 79

Brand: ST Pages: 67

Brand: Adaptec Pages: 2

Brand: MSI Pages: 90

Brand: Vibe Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands